YOKOGAWA DLM4038 - Page 287

5-254
IM DLM4038-17EN
:TRIGger{[:ATRigger]|:BTRigger}:CAN:
IDOR:IDENtifier:PFORmat
Function Sets or queries the ID input format, which is
one of the ID OR conditions, for CAN bus signal
triggering.
Syntax
:TRIGger{[:ATRigger]|:BTRigger}:CAN:
IDOR:IDENtifier:PFORmat {BINary|HEXa
|MESSage}
:TRIGger{[:ATRigger]|:BTRigger}:CAN:
IDOR:IDENtifier:PFORmat?
Example
:TRIGGER:ATRIGGER:CAN:IDOR:IDENTIFIE
R:PFORMAT BINARY
:TRIGGER:ATRIGGER:CAN:IDOR:IDENTIFIE
R:PFORMAT?
-> :TRIGGER:ATRIGGER:CAN:IDOR:IDENTI
FIER:PFORMAT BINARY
:TRIGger{[:ATRigger]|:BTRigger}:CAN:
IDOR:MSIGnal<x>:MESSage:ITEM
Function Sets the message item, which is one of the ID
OR conditions, for CAN bus signal triggering.
Syntax
:TRIGger{[:ATRigger]|:BTRigger}:CAN:
IDOR:MSIGnal<x>:MESSage:ITEM {<Strin
g>}
<x> = 1 to 4
<String> = Up to 32 characters
Example
:TRIGGER:ATRIGGER:CAN:IDOR:MSIGNAL1:
MESSAGE:ITEM "TEST"
:TRIGger{[:ATRigger]|:BTRigger}:CAN:
IDOR:RTR
Function Sets or queries the RTR value, which is one
of the ID OR conditions, for CAN bus signal
triggering.
Syntax
:TRIGger{[:ATRigger]|:BTRigger}:CAN:
IDOR:RTR {<Boolean>}
:TRIGger{[:ATRigger]|:BTRigger}:CAN:
IDOR:RTR?
Example
:TRIGGER:ATRIGGER:CAN:IDOR:RTR ON
:TRIGGER:ATRIGGER:CAN:IDOR:RTR?
-> :TRIGGER:ATRIGGER:CAN:IDOR:RTR 1
:TRIGger{[:ATRigger]|:BTRigger}:CAN:
MODE
Function Sets or queries the CAN bus signal trigger mode
setting.
Syntax
:TRIGger{[:ATRigger]|:BTRigger}:CAN:
MODE {EFRame|IDData|IDOR|SOF}
:TRIGger{[:ATRigger]|:BTRigger}:CAN:
MODE?
Example
:TRIGGER:ATRIGGER:CAN:MODE EFRAME
:TRIGGER:ATRIGGER:CAN:MODE?
-> :TRIGGER:ATRIGGER:CAN:MODE EFRAME
:TRIGger{[:ATRigger]|:BTRigger}:CAN:
RECessive
Function Sets or queries the CAN bus signal trigger
recessive level.
Syntax
:TRIGger{[:ATRigger]|:BTRigger}:CAN:
RECessive {HIGH|LOW}
:TRIGger{[:ATRigger]|:BTRigger}:CAN:
RECessive?
Example
:TRIGGER:ATRIGGER:CAN:RECESSIVE HIGH
:TRIGGER:ATRIGGER:CAN:RECESSIVE?
-> :TRIGGER:ATRIGGER:CAN:RECESSIVE H
IGH
:TRIGger{[:ATRigger]|:BTRigger}:CAN:
SOURce
Function Sets or queries the CAN bus signal trigger source
signal.
Syntax
:TRIGger{[:ATRigger]|:BTRigger}:CAN:
OURce {<NRf>}
:TRIGger{[:ATRigger]|:BTRigger}:CAN:
SOURce?
<NRf> = 1 to 8
Example
:TRIGGER:ATRIGGER:CAN:SOURCE 1
:TRIGGER:ATRIGGER:CAN:SOURCE?
-> :TRIGGER:ATRIGGER:CAN:SOURCE 1
:TRIGger{[:ATRigger]|:BTRigger}:CAN:
SPOint
Function Sets or queries the CAN bus signal trigger
sample point.
Syntax
:TRIGger{[:ATRigger]|:BTRigger}:CAN:
SPOint {<NRf>}
:TRIGger{[:ATRigger]|:BTRigger}:CAN:
SPOint?
<NRf> = 18.8 to 90.6
Example
:TRIGGER:ATRIGGER:CAN:SPOINT 18.8
:TRIGGER:ATRIGGER:CAN:SPOINT?
-> :TRIGGER:ATRIGGER:CAN:SPOINT 18.8
:TRIGger{[:ATRigger]|:BTRigger}:CAN
FD?
Function Queries all CAN FD bus signal trigger settings.
Syntax
:TRIGger{[:ATRigger]|:BTRigger}:CAN
FD?
5.34 TRIGger Group