YOKOGAWA WT110 User Manual

IM 253401-01E
App2-10
Appendix 2.3 Commands
Command Description Page
RELay Group
RELay? Queries all settings related to the comparator function. App. 2-28
:RELay:DISPLay Sets/queries the comparator display OFF, or in case of ON, the channel to be
displayed. App. 2-28
:RELay:HCHannel<x>? Queries all settings related to relay output items in case of harmonic analysis. App. 2-28
:RELay:HCHannel<x>:FUNCtion Sets/queries function of the relay output item in case of harmonic analysis. App. 2-29
:RELay:HCHannel<x>:THReshold Sets/queries the threshold level for the relay output item. App. 2-29
:RELay:MODE Sets/queries the mode of the comparator function. App. 2-29
:RELay:NCHannel<x>? Queries all settings related to the relay output items in case of normal
measurement. App. 2-29
:RELay:NCHannel<x>:FUNCtion Sets/queries the function of the relay output in case of normal measurement. App. 2-29
:RELay:NCHannel<x>:THReshold Sets/queries the threshold level for the relay output item. App. 2-29
:RELay:STATe Sets/queries the comparator function ON/OFF. App. 2-29
SAMPle Group
:SAMPle? Queries all settings related to sampling. App. 2-30
:SAMPle:HOLD Sets/queries to hold the output of data (display, communication). App. 2-30
STATus Group
:STATus? Queries all settings related to the status of communication. App. 2-31
:STATus:CONDition? Queries the contents of the condition filter and clears it at the same time. App. 2-31
:STATus:EESE Sets/queries the extended event register. App. 2-31
:STATus:EESR? Queries the contents of the extended event register and clears it. App. 2-31
:STATus:ERRor? Queries the occurred error code and message. App. 2-31
:STATus:FILTer<x> Sets/queries the transit filter. App. 2-31
:STATus:QMESsage Sets/queries whether or not to apply the corresponding message to the
query “ STATus:ERRor? ”. App. 2-31
:STATus:SPOLl?(Serial Poll) Executes serial polling. App. 2-31
STORe Group
:STORe? Queries all settings related to storing data. App. 2-32
:STORe:INTerval Sets/queries the interval for storing data. App. 2-32
:STORe:PANel Saves the set-up parameters to a file. App. 2-32
:STORe[:STATe] Sets/queries the store function ON/OFF. App. 2-32
Common Command Group
*CLS Clears the standard event register, extended event register and error queue. App. 2-33
*ESE Sets/queries the value of the standard event enable register. App. 2-33
*ESR? Sets/queries the value of the standard event register and clears it. App. 2-33
*IDN? Queries the instrument model. App. 2-33
*OPC This command is not supported by this instrument. App. 2-33
*OPC? This command is not supported by this instrument, and is always “ 1 ”. App. 2-33
*OPT? Queries installed options. App. 2-34
*PSC Sets/queries whether or not to clear some registers at power ON. App. 2-34
*RST Initializes the present settings. App. 2-34
*SRE Sets/queries the value of the service request enable register. App. 2-34
*STB? Queries the value of the status byte register. App. 2-34
*TRG Executes the same operation as the TRIG(SHIFT+HOLD) key. App. 2-34
*TST? Executes a self-test and queries the results. App. 2-34
*WAI This command is not supported by this instrument. App. 2-34

YOKOGAWA WT110 Specifications

General

Brand	YOKOGAWA
Model	WT110
Category	Measuring Instruments
Language	English