Index-1
IM 760401-01E
Index
Index
Index
command .......................................................................... 14-5
command List (IEEE 488.2) ............................................ 14-11
commands (before IEEE 488.2) ........................................ 13-1
commands list (before the IEEE 488.2) .......................... 10-16
Common command group .............................................. 14-42
common command header ............................................... 14-5
common mode voltage ...................................................... 16-2
COMMunicate goup ........................................................ 14-16
communication commands for adjustment ....................... 15-5
communication functions .................................................... 1-5
communication interface ....................................................... iii
comparator display ............................................................ 9-18
comparator function ............................................................ 1-5
comparator limit ................................................................ 9-15
comparator limit values ..................................................... 9-13
comparator mode ..............................................................9-12
comparator modes .............................................................. 9-9
compound header ............................................................. 14-5
computation end ............................................................... 10-4
computation function ........................................................... 1-4
computation method of harmonic distortion ........................ 7-5
computation over display .................................................... 2-4
computation over display (harmonic) .................................. 7-3
condition register ............................................................. 14-47
CONFigure group ............................................................ 14-18
contact relay ........................................................................ 9-9
contents of the package ........................................................ iii
continous integration mode ................................................. 6-2
continuous maximum allowable input ....................... 3-5, 16-2
continuous maximum common mode voltage ................... 16-2
control integration ............................................................... 9-3
corrective actions ............................................................ 15-14
crest factor ............................................ 4-24, 4-33, 5-8, 16-5
CT ratio ............................................................................. 4-12
current ................................................................................. 5-2
current frequency ................................................................ 5-6
current input .......................................................................... iv
current input is small ......................................................... 6-11
D
D/A output ........................................................................... 9-5
D/A output function ............................................................. 1-4
D/A output voltage .............................................................. 9-8
data ................................................................................... 14-7
data format ........................................................................11-7
data format (ASCII 488.2) ................................... 14-32, 14-33
data format (ASCII) ................................................. 10-5, 10-9
data format (BINARY) ..................................................... 14-35
data section ....................................................................... 10-6
DC .......................................................................................4-1
dead lock ........................................................................... 14-5
deg ...................................................................................... 5-4
digital characters ................................................................. 1-6
digital numbers .................................................................... 1-6
dimensional drawings ..................................................... 16-15
display function of integrator values .................................... 6-3
display functions ................................................................. 1-3
DISPlay group ................................................................. 14-22
display hold (harmonic) ....................................................... 7-2
display range ..................................................................... 16-9
display resolution during integration ................................... 6-3
display update ................................................................... 4-32
display update rate (harmonic) ........................................... 7-2
Symbols
<ESC>C ............................................................................ 11-8
<ESC>L ............................................................................ 11-8
<ESC>R ............................................................................ 11-8
<ESC>S ............................................................................ 11-8
1P2W ................................................................................ 3-11
1P3W ................................................................................ 3-11
24-pin connector ................................................................... iv
3P3W ................................................................................ 3-12
3P4W ................................................................................ 3-12
3V3A ................................................................................. 3-12
488.2 mode ...................................................................... 11-1
488.2 mode ....................................................................... 10-1
A
accuracy ............................................................................ 16-3
active power ........................................................................5-2
active power accuracy ...................................................... 16-4
address ........................................................................... 10-12
addressable mode ............................................................ 10-1
adjusting ............................................................................ 15-1
adjusting the current range ............................................... 15-3
adjusting the D/A output .................................................... 15-4
adjusting the voltage range ............................................... 15-2
aliasing (harmonic) .............................................................. 7-3
ampere hour ................................................................ 6-1, 6-7
AOUTput group ............................................................... 14-15
apparent power ................................................................... 5-3
ASCII character codes .................................................... 14-60
attenuation constant .......................................................... 4-18
auto range ........................................................................... 4-8
auto range (harmonic) ......................................................... 7-2
auto range monitor ..............................................................2-4
average active power ................................................ 4-30, 5-8
averaging function ............................................................. 4-18
averaging function (harmonic) ............................................ 7-3
B
back-up of setup parameters ............................................ 12-1
backup during power failures ............................................ 6-10
backup function ................................................................... 1-5
backus-naur form .............................................................. 14-3
bar display ........................................................................... 2-4
bar display (harmonic) ........................................................ 7-3
baud rate ........................................................................... 11-7
block data .......................................................................... 14-9
block diagram ...................................................................... 1-1
BNF notation ..................................................................... 14-3
boolean ............................................................................. 14-8
C
calibration .......................................................................... 15-6
calibration of AC voltage, current and power .................... 15-8
calibration of D/A output .................................................. 15-10
calibration of DC voltage, current and power .................... 15-6
CCITT ............................................................................... 11-4
character data ................................................................... 14-8
character string data ......................................................... 14-8
check these items first .................................................... 15-13
To Next Page
Loading...
Need help?
General
