EMC Filters
II K A-6
Appendix A
Three-phase filters
EMC mains filters are necessary so as to
comply with EN 50 081 if a power converter
is to be operated at a public low-voltage
grid, in Europe, for example, with 400 V
between the phases. Grids of this kind
have an earthed neutral conductor. For
these cases, ABB offers its three-phase
mains filters for 500 V and 25 A ... 1000 A.
On local lines inside factories they do not
supply sensitive electronics. Therefore
converters do not need EMC filters.
In chapter
5.2 Installation in accordance
with EMC
the topic EMC filter is described.
Converter type Rat. direct current Filter type Dimensions
L x W x H
[A] [kg] [mm]
2-quadr. convert.
DCS401.0020 20 NF3-500-25 3 250x150x65
DCS401.0045 45 NF3-500-50 3.1 250x150x65
DCS401.0065 65 NF3-500-64 3.1 250x150x65
DCS401.0090 90 NF3-500-80 9.5 450x170x90
DCS401.0125 125 NF3-500-110 9.5 450x170x90
DCS401.0180 180 NF3-500-320 21 400x260x115
DCS401.0230 230 NF3-500-320 21 400x260x115
DCS401.0315 315 NF3-500-320 21 400x260x115
DCS401.0405 405 NF3-500-320 21 400x260x115
DCS401.0500 500 NF3-500-600 22 450x260x115
DCS401.0610 610 NF3-500-600 22 450x260x115
DCS401.0740 740 NF3-500-600 22 450x260x115
DCS401.0900 900 NF3-690-1000 ➋ ➋
4-quadr. convert.
DCS402.0025 25 NF3-500-25 3 250x150x65
DCS402.0050 50 NF3-500-50 3.1 250x150x65
DCS402.0075 75 NF3-500-80 9.5 450x170x90
DCS402.0100 100 NF3-500-80 9.5 450x170x90
DCS402.0140 140 NF3-500-110 9.5 450x170x90
DCS402.0200 200 NF3-500-320 21 400x260x115
DCS402.0260 260 NF3-500-320 21 400x260x115
DCS402.0350 350 NF3-500-320 21 400x260x115
DCS402.0450 450 NF3-500-600 22 450x260x115
DCS402.0550 550 NF3-500-600 22 450x260x115
DCS402.0680 680 NF3-500-600 22 450x260x115
DCS402.0820 820 NF3-690-1000 ➋ ➋
DCS402.1000 1000 NF3-690-1000 ➋ ➋
The filters 25 ... 600 A are available for 440 V and for 500 V.
➊ The filters can be optimized to suit the actual motor currents
encountered:
I
Filter
= 0,8 • I
MOT max
; the factor 0.8 takes into account the current
ripple.
➋ Weight and dimensions on request
➊
Weight
appr.
Fig. A/7: Dimensions of filter
Table A/6: Main filter data
Filter type max. I
N
A B C D Fixing dimensions Connection Weight PE
voltage E Æ F F' G G' bar with Term. kg
appr. hole Æ (mm²)*
NF3-500-25 500 25 250 150 65 1 6.5 115 136 4 3.0 M6
NF3-500-50 500 50 250 150 65 1 6.5 115 136 10/16 3.1 M6
NF3-500-64 500 64 250 150 65 1 6.5 115 136 10/16 3.1 M6
NF3-500-80 500 80 427 170 90 1 6.5 373 130 25/35 9.5 M10
NF3-500-110 500 110 436 170 90 1 6.5 373 130 50 9.5 M10
NF3-500-320 500 320 450 285 171 1 12 240 235 11 21 M10
NF3-500-600 500 600 590 305 158 1 12 290 235 11 22 M10
* single cor / litz wire
Line
Load
A
B
F’
F
G’
G
E
C
D
Fig. A/8: Drawing of filter
To Next Page
Loading...
