Agilent Technologies N5230C User Manual

Index
Service Guide N5230-90024 Index-9
in hard disk drive assembly, all options
part numbers
, 6-42
in internal analyzer, all options
illustrated
, 6-37
part numbers
, 6-36
in rear panel assembly, all options
illustrated
, 6-41
part numbers
, 6-40
in top assembly, all options
illustrated
, 6-33
part numbers
, 6-32
password
Agilent administrator, 7-45
performance
tests
calibration coefficients
, 3-33
description of
, 3-7
dynamic accuracy
, 3-34
frequency accuracy
, 3-30
noise floor
, 3-31
receiver compression
, 3-31
source maximum power output
,
3-29
source power accuracy
, 3-28
source power linearity
, 3-29
test port output maximum power,
3-29
test port output power accuracy
,
3-28
test port output power linearity
, 3-29
trace noise
, 3-30
tests, N7840A, 3-28
verification
ANSI/NCSL Z540-1-1994
, 3-8
non-ANSI/NCSL Z540-1-1994, 3-9
phase stability check
failure of, 3-16
test port cables
, 3-15
pin assignments
connectors
AUX I/O
, 5-14
HANDLER I/O
, 5-13
TEST SET I/O, 5-12
ping
command, LAN, 4-19
from network
, 4-20
to analyzer, 4-19
pixel
damaged, 4-15
definition
, 4-15
Port 1
attenuator
removal and replacement
, 7-38
check
, 3-10
typical power output, 4-35
Port 2
attenuator
removal and replacement
, 7-38
check
, 3-10
typical power output
, 4-36
post-repair procedures , 7-54
power supply
check, 4-7
functional description of
, 5-5
functional group
, 5-3
if all voltages are missing, 4-9
operation
, 5-26
voltage checks
, 4-8
power supply assembly
illustrated, 6-13
part number
, 6-12
removal and replacement
illustrated
, 7-15
procedure
, 7-14
troubleshooting
, 4-7
power, source
accuracy test, 3-28
linearity test
, 3-29
power, source output
maximum test, 3-29
power, test port output
accuracy test, 3-28
linearity test
, 3-29
maximum test
, 3-29
pre-repair
procedures
caution about
, 7-3
warnings about
, 7-3
preventive maintenance
effect on error terms, 8-3
processing subgroup
operation, 5-24
protection
against EMI/RFI, 6-47
against ESD, 1-6, 3-4, 4-3, 7-3, 8-4
protective end caps
for connectors
part numbers
, 6-46
pulse I/O adapter, N1966A , 2-6
R
R1 channel
troubleshooting, 4-25
R1 trace
troubleshooting, 4-25, 4-27
R2 channel
troubleshooting, 4-25
R2 trace
troubleshooting, 4-25, 4-27
rack mount kits
part numbers, 6-48
with handles, Option 1CP
, 2-4
without handles, Option 1CM, 2-4
RAM, main
operation, 5-24
rear panel
connectors
1284-C
, 5-25
AUX I/O, 5-11
Display
, 5-25
EXT 10 MHz REF IN
, 5-10
GPIB, 5-24
HANDLER I/O
, 5-11
LAN
, 5-25
PARALLEL, 5-25
RS-232
, 5-24
SERIAL
, 5-24
TEST SET I/O, 5-11
TRIG IN
, 5-11
TRIG OUT
, 5-11
USB
, 5-24
VGA
, 5-25
interconnects
, 5-10, 5-11, 5-24
replaceable parts
illustrated
, 6-41
part numbers
, 6-40
troubleshooting
, 4-17
rebuilt-exchange assemblies
program, 6-5
receiver
accuracy
dynamic accuracy test, 3-34
calibration
, 3-39
compression test
, 3-31
dynamic accuracy test, 3-34
functional description of
, 5-4
functional group
, 5-3
linearity
dynamic accuracy test
, 3-34
outputs
troubleshooting
, 4-39
receiver display
running the test, 4-25
receiver group
block diagram, 5-20
defined, 4-26
operation
, 5-19
troubleshooting
, 4-39
recovery
option data, 8-16
recovery, operating system , 8-19
reference channel R1, See R1 channel
reference channel R2, See R2 channel
reflection tracking
cause of failure, 8-12
definition of
, 8-12
measurements affected by, 8-12
removing
assemblies, See specific assembly.
options
, 8-15
parts, See specific part.
removing the cover , 1-4
repair
post-repair procedures, 7-54
procedures

Agilent Technologies N5230C Specifications

General

Brand	Agilent Technologies
Model	N5230C
Category	Measuring Instruments
Language	English