Index
Service Guide N5230-90024 Index-11
analyzer covers
illustrated
, 7-7
procedure, 7-6
assembly
cautions about
, 7-4
list of procedures, 7-5
sequence
, 6-4, 7-4
warnings about
, 7-4
fan, 7-48
front panel assembly
illustrated
, 7-9
procedure, 7-8
front panel subassemblies
illustrated
, 7-11
procedures
, 7-10
inverter board
illustrated
, 7-11
procedure
, 7-10
lithium battery
illustrated
, 7-53
procedure
, 7-52
midweb
illustrated
, 7-49
procedure, 7-48
touch screen controller board
illustrated
, 7-11
procedure, 7-10
touch screen display
illustrated
, 7-13
touch screen display assembly
illustrated
, 7-11
procedure
, 7-13
USB connector board
illustrated
, 7-11
procedure
, 7-12
replacement sequence
, 4-3
return loss check
failure of, 3-13
test port cables
, 3-13
RFI/EMI
supplies
part numbers, 6-47
rotary pulse generator (RPG)
illustrated, 6-9
part number
, 6-8
test, 4-15
troubleshooting
, 4-12
RS-232 port
rear panel connector, 5-24
troubleshooting, 4-18
S
safety
considerations, 1-3
earth ground
, 1-3
symbols, 1-3
SCPI
, 8-9
screws
for bottom assemblies
illustrated
, 6-35
part numbers, 6-34
in external analyzer
illustrated
, 6-39
part numbers, 6-38
in hard disk drive assembly
part numbers
, 6-42
in rear panel assembly
illustrated
, 6-41
part numbers
, 6-40
serial number
changing, 8-17
installing
, 8-17
SERIAL port
rear panel connector, 5-24
troubleshooting
, 4-18
service
contacting Agilent, 2-10
EMI/RFI parts
part numbers
, 6-47
miscellaneous parts
required
, 2-9
options, 2-10
procedures
caution about
, 7-3
post-repair, 7-54
warnings about
, 7-3
static safety parts
part numbers
, 6-47
required
, 2-9
test equipment
required
, 2-7
tools
part numbers
, 6-46
required
, 2-9
warnings
, 1-4
warranty
one-year return to Agilent
, 2-10
standard
, 2-10
shipment for service or repair
, 2-11
signal separation
functional description of, 5-4
functional group, 5-3
signal separation group
defined, 4-26
operation
, 5-15
troubleshooting, 4-35
signal separation group, configurable test
set
block diagram, 5-17
signal separation group, standard test set
block diagram, 5-15
single band failure
, 4-28
software
options, 8-15
source
calibration, 3-38
functional group, 5-3
maximum output power test
, 3-29
power accuracy test, 3-28
power linearity test
, 3-29
source attenuators
illustrated, 6-21, 6-29
operation, 5-16
part number
, 6-20, 6-28
removal and replacement
illustrated
, 7-39
procedure
, 7-38
source attenuators, Option 1E1
description of, 2-5
source attenuators, Option 1E1
illustrated, 6-21, 6-29
part number
, 6-20, 6-28
source group
block diagram, 5-7
defined
, 4-26
operation
, 5-6
troubleshooting
, 4-28
source match
cause of failure, 8-11
definition of
, 8-11
measurements affected by
, 8-11
SPAM board
illustrated, 6-13
operation
analog
, 5-19
digital, 5-24
part number
, 6-12
removal and replacement
illustrated
, 7-17
procedure
, 7-16
troubleshooting
, 4-39
speaker
front panel, 5-23
troubleshooting
, 4-12
specifications
instrument, 3-6
stabilization, warm up time, 3-4
system
, 3-6
stabilization
warm up time, 3-4
standards compliant calibration
built-in tests, Option 898, 2-5
static safety parts
required for servicing, 2-9
step attenuator, source
illustrated, 6-21, 6-29
operation, 5-16
part number
, 6-20, 6-28
port 1
troubleshooting
, 4-38
port 2
troubleshooting
, 4-38
removal and replacement
illustrated
, 7-39
procedure
, 7-38