Need help?Do you have a question about the Allied Systems Freeman 370 and is the answer not in the manual?
General| Brand | Allied Systems |
|---|---|
| Model | Freeman 370 |
| Category | Farm Equipment |
| Language | English |
General safety warnings and information for baler operation and maintenance.
Explanation of symbols and terms used to emphasize safety precautions.
Defines the baler's intended purpose and limitations.
Critical safety rules and precautions for operating the baler.
Hazards associated with pressurized hydraulic systems and safe servicing practices.
Procedures and precautions for safe maintenance, lubrication, and repair.
Guidelines for using appropriate safety equipment during operation and maintenance.
Risks associated with the baler's electrical system and precautions.
Hazards related to hot oil and precautions during servicing.
Risks associated with compressed air use and safety measures.
Warnings and precautions regarding fire hazards related to fuel and hydraulic oil.
Recommendations for carrying and using fire extinguishers.
Procedures for handling and extinguishing fires involving the baler.
Location and importance of the baler's unique serial number.
Location of the serial number for the baler's power unit.
Explanation of the format and meaning of the baler serial number.
Procedure for checking and maintaining the correct gearbox oil level.
Intervals and procedure for changing gearbox oil.
Schedule and procedure for checking crank arm bolt torque.
Greasing schedule for connecting rod and crank arm bearings.
Explanation of the 5-column format used for parts lists.
List and diagram of parts for the front end installation.
Diagram and components for the right-hand side mount.
Diagram and components for the left-hand side mount.
Diagram and components for the lever mechanism.
Diagram and components for the bracket assembly.
Overview of engine parts and their installation points.
Procedure for mounting the battery strap and cables to the engine.
Diagram showing flywheel belt mounting on the baler.
Instructions for mounting the engine belly pan to the front end assembly.
Diagrams and notes for installing the air cleaner assembly.
Diagram and list of parts for the engine assembly.
Procedure for installing the starter and solenoid.
Instructions for installing the engine manifold with associated fittings.
Procedure for installing the engine wiring harness and control box.
Instructions for shimming the gearbox for proper alignment.
Procedure for setting the timing between the drive arm and shaft.
Procedure for installing the cap and adjusting the gap with shims.
Instructions for shimming the gearbox for proper alignment.
Procedure for setting the timing between the drive arm and shaft.
Procedure for installing the cap and adjusting the gap with shims.
Instructions for shimming the gearbox for proper alignment.
Procedure for setting the timing between the drive arm and shaft.
Procedure for installing the cap and adjusting the gap with shims.
Instructions for shimming the gearbox for proper alignment.
Procedure for setting the timing between the drive arm and shaft.
Procedure for installing the cap and adjusting the gap with shims.
List and diagram of major gearbox assembly parts.
Procedures for measuring critical gearbox shaft tolerances.
Notes and requirements for assembling the knotter drive chain.
Diagrams showing components for LH shield installation.
Diagram and parts for installing shields on the crank arm.
Specifications for plunger knife extension and recess.
Torque specifications for installing the plunger assembly bearing.
Diagrams illustrating different views of the plunger assembly.
Specifications for plunger knife extension and recess.
Torque specifications for installing the plunger assembly bearing.
Diagrams illustrating different views of the plunger assembly.
Specifications for plunger knife extension and recess.
Torque specifications for installing the plunger assembly bearing.
Diagrams illustrating different views of the plunger assembly.
Specifications for plunger knife extension and recess.
Torque specifications for installing the plunger assembly bearing.
Diagrams illustrating different views of the plunger assembly.
Notes regarding clearance, torque, and lubrication for the connecting rod assembly.
Notes regarding clearance, torque, and lubrication for the connecting rod assembly.
Diagrams and components for dual rams and their mounts.
Installation of back plate and mount plate components.
Installation of tension rail components.
Diagrams and components for dual rams and their mounts.
Installation of back plate and mount plate components.
Installation of tension rail components.
Diagrams and components for dual rams and their mounts.
Installation of back plate and mount plate components.
Installation of tension rail components.
Diagrams and components for dual rams and their mounts.
Installation of back plate and mount plate components.
Installation of tension rail components.
Diagrams and components for rear bar bracket installation.
Diagrams and components for tension rail installation.
Diagram and parts for the 16-inch frame and axle assembly.
Diagram and parts for the 14x21-inch frame and axle assembly.
Components and procedure for RH side chamber installation.
Installation of left and right hand chamber rails.
Components and procedure for lower center chamber installation.
Components for lower center front installation.
Components for lower left plunger rail and spacer installation.
Components for lower bottom frame rail installation.
Components for upper and lower frame rail installation.
Components for lower center rear installation.
Components for spring mounts and spacers.
To Next Page