To Next PageTo Next Page
Need help?Do you have a question about the Ametek 2003RP and is the answer not in the manual?
General| Brand | Ametek |
|---|---|
| Model | 2003RP |
| Category | Power Supply |
| Language | English |
Official trademarks and product names associated with the company.
Copyright statement for the user and programming manual.
Disclaimer regarding documentation accuracy and liability.
Manual revision date and version information.
Identifier for the specific manual document.
Company contact details for sales, service, and general inquiries.
Visual indicators used to denote safety warnings and precautions.
Steps required for returning a defective product for repair or replacement.
Overview of the 2003RP AC power source models and capabilities.
Information on compatible rack mounting accessories.
Detailed electrical input and output parameters.
Additional typical performance specifications.
Specifications for optional measurement functions.
System-level features like interface capabilities.
Protection mechanisms against overcurrent and overtemperature.
Physical dimensions, weight, and connectors.
Operating and storage environmental conditions.
Compliance with safety and emissions standards.
Description of front panel knobs, buttons, and displays.
Details on optional hardware and software features.
Guidance on inspecting and unpacking the unit.
Specifications for AC input power connection.
Details on supported AC input voltage ranges.
Information on the unit's line frequency range.
Notes on input power usage.
Procedure for setting the input voltage range.
Instructions for physical mounting and installation.
Steps for correctly wiring the AC input power.
How to connect loads to the AC source output.
Description of available output voltage settings.
Steps to verify the unit's operational status.
Explanation of Constant Current and Constant Voltage modes.
Description of front panel components: indicators, knobs, buttons, and displays.
Step-by-step guides for common operational tasks.
Procedure to configure default power-on settings.
Explanation of Constant Current and Constant Voltage modes.
Details on the Function Strobe output signal.
Using the Remote Inhibit input for output control.
Brief introduction to circuit explanations.
High-level block diagram and component functions.
Description of the DC power supply circuitry.
Role of the mother board in signal routing.
Details on the switched mode amplifier modules.
Function of the oscillator assembly for signal generation.
Explanation of the voltage range selection relays.
Function of the output board and relays.
Description of optional communication interfaces.
List of necessary test equipment for calibration.
Steps to enter and navigate calibration modes.
Procedure for standard periodic calibration.
Calibrating measurements at low scales.
Calibrating measurements at full scales.
Adjustments not required on a routine basis.
Procedure for adjusting high current measurement range.
Procedure for adjusting the current limit setting.
Procedure for adjusting the open sense function.
Introduction to maintenance and troubleshooting.
Guidelines for cleaning the unit's exterior.
Key points for basic operational understanding.
Diagnosing and resolving common operational problems.
Instructions for removing internal modules.
List of components available for replacement.
Overview of remote control capabilities.
System requirements for the PGUI32 control software.
Setting up and using the IEEE-488 interface.
Setting up and using the RS232C serial interface.
Diagram for constructing the RS232C communication cable.
Instructions for installing the PGUI32 software.
Resolving problems with RS232C communication.
Resolving problems with IEEE-488/GPIB communication.
List of files included with the PGUI32 software.
How to register and access software updates.
Understanding syntax and formatting conventions.
Types and structure of SCPI commands.
Hierarchical structure of SCPI commands.
How to retrieve data using SCPI queries.
Format of SCPI messages.
Data types used in SCPI communication.
Considerations for bus communication speed.
Categorization of SCPI commands by subsystem.
SCPI commands for unit calibration.
SCPI commands for measurements.
SCPI commands for output source parameters.
SCPI commands for controlling output functions.
SCPI commands for system-level functions.
Standard IEEE 488.2 common commands.
Overview of programming examples provided.
Timing advice for programming commands.
Examples for setting voltage, frequency, and current.
Examples for retrieving measurement data using SCPI.
Initial state of status registers upon power-up.
Explanation of the Standard Event Status register.
Description of the Status Byte register contents.
Examples demonstrating status register usage.
