• Klass 1 Laser Apparat
Electromagnetic Compatibility (EMC) Standards
This product complies with and conforms to the following
international EMC standards, as applicable:
• CISPR 22, including all national standards based on CISPR
22.
• CISPR 24, including all national standards based on CISPR
24.
• IEC 61000-3-2 and IEC 61000-3-3.
Avaya Inc. is not responsible for any radio or television interference
caused by unauthorized modifications of this equipment or the
substitution or attachment of connecting cables and equipment other
than those specified by Avaya Inc. The correction of interference
caused by such unauthorized modifications, substitution or
attachment will be the responsibility of the user. Pursuant to Part 15
of the Federal Communications Commission (FCC) Rules, the user is
cautioned that changes or modifications not expressly approved by
Avaya Inc. could void the user’s authority to operate this equipment.
Federal Communications Commission Part 15 Statement:
For a Class A digital device or peripheral:
Note:
This equipment has been tested and found to comply with the
limits for a Class A digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is
operated in a commercial environment. This equipment
generates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the instruction
manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential
area is likely to cause harmful interference in which case the
user will be required to correct the interference at his own
expense.
For a Class B digital device or peripheral:
Note:
This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful
interference to radio communications. However, there is no
guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following
measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and
receiver.
• Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV
technician for help.
Equipment With Direct Inward Dialing (“DID”):
Allowing this equipment to be operated in such a manner as to not
provide proper answer supervision is a violation of Part 68 of the
FCC’s rules.
Proper Answer Supervision is when:
1. This equipment returns answer supervision to the public
switched telephone network (PSTN) when DID calls are:
• answered by the called station,
• answered by the attendant,
• routed to a recorded announcement that can be
administered by the customer premises equipment
(CPE) user
• routed to a dial prompt
2. This equipment returns answer supervision signals on all
(DID) calls forwarded back to the PSTN.
Permissible exceptions are:
• A call is unanswered
• A busy tone is received
• A reorder tone is received
Avaya attests that this registered equipment is capable of providing
users access to interstate providers of operator services through the
use of access codes. Modification of this equipment by call
aggregators to block access dialing codes is a violation of the
Telephone Operator Consumers Act of 1990.
Automatic Dialers:
When programming emergency numbers and (or) making test calls to
emergency numbers:
• Remain on the line and briefly explain to the dispatcher the
reason for the call.
• Perform such activities in the off-peak hours, such as early
morning or late evenings.
Toll Restriction and least Cost Routing Equipment:
The software contained in this equipment to allow user access to the
network must be upgraded to recognize newly established network
area codes and exchange codes as they are placed into service.
Failure to upgrade the premises systems or peripheral equipment to
recognize the new codes as they are established will restrict the
customer and the customer’s employees from gaining access to the
network and to these codes.
For equipment approved prior to July 23, 2001:
This equipment complies with Part 68 of the FCC rules. On either the
rear or inside the front cover of this equipment is a label that
contains, among other information, the FCC registration number, and
ringer equivalence number (REN) for this equipment. If requested,
this information must be provided to the telephone company.
For equipment approved after July 23, 2001:
This equipment complies with Part 68 of the FCC rules and the
requirements adopted by the Administrative Council on Terminal
Attachments (ACTA). On the rear of this equipment is a label that
contains, among other information, a product identifier in the format
US:AAAEQ##TXXX. If requested, this number must be provided to
the telephone company.
The REN is used to determine the quantity of devices that may be
connected to the telephone line. Excessive RENs on the telephone
line may result in devices not ringing in response to an incoming call.
In most, but not all areas, the sum of RENs should not exceed 5.0.
L’indice d’équivalence de la sonnerie (IES) sert à indiquer le nombre
maximal de terminaux qui peuvent être raccordés à une interface
téléphonique. La terminaison d’une interface peut consister en une
combinaison quelconque de dispositifs, à la seule condition que la
somme d’indices d’équivalence de la sonnerie de tous les dispositifs
n’excède pas cinq.
To be certain of the number of devices that may be connected to a
line, as determined by the total RENs, contact the local telephone
company. For products approved after July 23, 2001, the REN for
this product is part of the product identifier that has the format
US:AAAEQ##TXXX. The digits represented by ## are the REN
without a decimal point (for example, 03 is a REN of 0.3). For earlier
products, the REN is separately shown on the label.
Means of Connection:
Connection of this equipment to the telephone network is shown in
the following table:
To Next Page
Loading...
