B. Braun microspeed uni

Questions and Answers

M
Mrs. Diane UnderwoodSep 6, 2025
What does Error 1 mean on B. Braun microspeed uni?
- C
  Christine WrightSep 7, 2025
  Error 1 indicates that more than one key was pressed at the same time. Only press one key at a time.
H
Heather AndersonAug 22, 2025
What to do if B. Braun microspeed uni shows Error 6 – Motor?
- R
  Raymond GallagherAug 22, 2025
  Error 6 indicates a motor issue. This might be because no motor is connected to the control unit, so connect a motor. Alternatively, the motor itself could be defective and needs replacement, or the motor cable GD672 or GD673 may be faulty and require replacement.
H
Hannah SimmonsSep 4, 2025
What does Error 9 mean on B. Braun microspeed uni Medical Equipment, and how can I fix it?
- L
  Laura JonesSep 4, 2025
  Error 9 indicates that current cannot be properly applied to the motor. Replace the motor or motor cable.
S
Shelly MartinezSep 2, 2025
What does Error 5 – Select only one Motor mean on B. Braun microspeed uni Medical Equipment, and how do I resolve it?
- K
  Kathryn MillerSep 2, 2025
  Error 5 concerning motor selection indicates a speed request from the foot control while two motors are released for operation (motor release switch on motor cable GD672 is in the "ON" position). Release the required motor using the motor release switch (position "ON") and block the motor that is not required using the motor release switch (position "OFF"). The motor cable GD672 may also be defective and require replacement.
R
Richard MartinezSep 1, 2025
What causes Error 8 – Power Fail on B. Braun microspeed uni Medical Equipment?
- E
  ethanmurraySep 1, 2025
  Error 8 signals a power supply error. Verify that the mains voltage is within the defined range.
D
dwaynevargasAug 30, 2025
What to do if B. Braun Medical Equipment displays Error 6 – Motor blocked?
- S
  simmonsbillyAug 30, 2025
  If Error 6 indicates a blocked motor, stop motor actuation and release the blockage. If the error continues, the motor may be defective and require replacement.
L
laura98Aug 29, 2025
What does Error 5 – Select Motor mean on B. Braun microspeed uni Medical Equipment and how to fix it?
- G
  Gregory CalderonAug 29, 2025
  Error 5 regarding motor selection means that there is a speed request from the foot control while the motor is locked by the motor release switch on motor cable GD672 (position "OFF"). Set the motor release switch on the motor cable to the "ON" position. Alternatively, the motor cable GD672 may be defective and require replacement.
D
davisralphAug 27, 2025
Why does B. Braun microspeed uni show Error 7 - Motor overheated?
- K
  Katherine DaviesAug 28, 2025
  Error 7 indicates the motor has overheated. Allow the motor to cool down. If the error persists, the motor may need to be replaced.
C
Christine RobertsAug 27, 2025
What does Error 4 – Hand-Control mean on B. Braun Medical Equipment, and how can I fix it?
- E
  Eric MoralesAug 27, 2025
  Error 4 indicates a problem with the hand control. This can happen if the lever of motor cable GD673 or the trigger of pistol handpiece GD684 was activated during the automatic test; release the lever or trigger. If that doesn't work, the motor cable GD673 or the pistol handpiece GD684 may be defective and need replacement.
J
Jonathan HamptonAug 25, 2025
What does Error 6 – Motor/Hallsensor mean on B. Braun Medical Equipment, and how to resolve it?
- M
  Melissa StevensAug 26, 2025
  Error 6 related to the Motor/Hallsensor indicates a malfunction in the Hall system of the motor (specifically for motors GD674, GD678, GD679, GD682, and GD684). In this case, replace the motor. This error could also be caused by a defective motor cable GD672 or GD673, which would also need to be replaced.