1. Safety
To prevent projector dam age
• Unplug this projec tor from the wall outlet before cleaning it. Do not use liquid aerosol cleaners. U se a damp soft cloth for
cleaning.
• Do not use this projector near water or in con tact with water.
• Do not use the projector with condensation on it. It can lead to breakdown or other failure.
• Never place the projector in direct sun light. S un light on the lens can severely damage the Digital M irror Devices
TM
in w hich
case there is a loss of warranty.
• Do not block the intake and exhaust v ents. If they are bloc ked, heat may be generated inside the projector, c ausing deterioration
in the projector quality a nd fire.
• Special care for Laser Beams : Special care should be used when DLP ® projectors are used in the s ame room as high pow er
laser equipment. Direct or indirect hitting of a laser beam on to the lens can severely da mage the Digital Mirr
or De vice s
TM
in
which case there is a loss of warranty.
• Save the original shipping carton and packing material. They will come in handy if you ever have to ship y our equipment. For
maximum protection, repac k y our s et as it w as o riginally packed a t the factory.
• For safety’s sake, refrain from setting the projector at any place subjec ted to high temperature a nd high humidity. Please
maintain an operating tem perature, humidity, and altitude as specified below.
- Allowable operating temperature is +41°F (+5°C) to +104°F (+40°C).
- Operating hum idity: between 30% and 90%
- Be sure to use this projector a t an altitude of less than 2000 meters.
2000m
• Never put any heat-producing device under the projector s o that the projector does not overheat.
• Do not attach the projector to a place that is unstable or subjected to vibration.
• Do not ins tall the projector near any equipment that produces a strong magnetic field.
Also refrain from installing near the
projector any cable carrying a large current.
• Place the projector on a solid, vibration free surface; otherwise it may fall, causing serious injury to a c hild or adult, and serious
damage to the product.
• Do not stand upright the projector; it m ay fall, causing serious injury and damage to the projector.
• Slanting the projector more than ± 10° (right and left) or ±15° (front and rear) m ay cause trouble or explosion o f the lam p.
• Do not place the projector near air-conditioning unit, heater, or humidifier to avoid hot
or mois t air to the exhaust and ventilation
hole of the projector.
• Do not place the projector in the following places. Otherwise, a short circuit, heat generation, or melting of the power co rd
coating may oc cur, causing fire, electric shock, product failure, o r de formation.
- Outdoors or non air-conditioned place.
- Place where a gas such as a hydrogen sulfide is generated (i.e. hot spring).
- Place w here there is too much s alt suc h as near the coast.
• Do not put any object that is heavy or larger than the outer frame on the projector. Otherwise, the object may fall losing its
balance and cause injury.
• Do not subject the projector to strong shocks or vibrations. Do not handle the projector roughly. The projector may be damaged,
resulting in fire or electric shock.
• Do not replace the lamp immediately after using the projector because the lamp would be extremely hot and it may cause burns.
• Depending on the installation conditions, w arm a ir that is emitted from the
exhaust vents m ay flow into the intake vent, causing
the projector to display “HIGH TE MP WARNING” and then stop projecting ima ges.
• Placing the projector directly on a carpet impairs ventilation by the fans, causing damage or failure. Put a hard board under the
projector to facilitate v entilation.
• Place the projector at least 50 cm (or 20 inches) away from the wa ll to prevent the intake vents and the exhaust vents that emit
hot air from b eing blocked.
R5905597 PHXX SERIES 20/05/2014
9
To Next Page
Loading...
Need help?
General
Weight and Dimensions
