BRUEL & KJAER PULSE 3560-C User Manual

CHAPTER 4
Introduction to Hardware
49
Table 4.1 Types and modules comprising PULSE front-ends (shaded cells are Dyn-X modules)
Type Product Name
Frequency
Range
Aux. Channels
Simultaneous
Channels
Connec-
tors
Input Type
Type 3560-B
3560-B-010
5-channel
PULSE Data
Acquisition Unit
0Hz to
25.6 kHz
16 Aux Input
d
(10 samples/s)
2 Digital Output
5 Input
1 Sine Output
LEMO
Direct/CCLD
a, b
/Mic. Preamp.
1 Tacho Conditioning
c
3560-B-110
3560-B-020
BNC
Direct/CCLD
a
1 Tacho Conditioning
c
3560-B-120
3560-B-030
5 Input
1 Generator
Output
LEMO
Direct/CCLD
a, b
/Mic. Preamp.
1 Tacho Conditioning
c
3560-B-130
3560-B-040
BNC
Direct/CCLD
a
1 Tacho Conditioning
c
3560-B-140
Types 3560-C, D, E CDE
3109
Generator,
4/2-ch. Input/
Output Module
0Hz to
25.6 kHz
–
4 Input
2 Generator
Output
LEMO
and
BNC
Direct/CCLD
a
/Mic. Preamp.
1 Tacho Conditioning
c
1 of these modules, up to 17 input channels
Up to 5 of these modules, up to 65 input channels Up to 8 of these modules, up to 96 input channels
3110
Generator,
2/1-ch. Input/
Output Module
0Hz to
204.8 kHz
2 Input
1 Generator
Output
e
3038
12-ch. Input
Module
0Hz to
25.6 kHz
12 Input
BNC
Direct/CCLD
a
2 Tacho Conditioning
c
3040
3038-B
2×Sub-D Direct/CCLD
a
/Mic. Preamp.
b
3040-B
3039
6-ch. Input
Module
6 Input
BNC
Direct/CCLD
a
/Mic. Preamp
1 Tacho Conditioning
c
3041
3039-B
Sub-D Direct/CCLD
a
/Mic. Preamp.
b
3041-B
3035
6-ch. Charge &
CCLD Input
Module
0Hz to
25.6 kHz
– 6 Input
BNT/
BNC
and TNC
Charge/Direct/CCLD
a
Tacho Conditioning on BNT
Connector
UA-1365 Blank Module –
7536
Controller
Module
–
16 Aux Input
d
(10 samples/s)
2 Digital Output
–
1 of these modules 1 of these modules 1 of these modules
7537
5/1-ch.
Input/Output
Controller
Module
0Hz to
25.6 kHz
5 Input
1 Sine Output
LEMO
Direct/CCLD
a, b
/Mic. Preamp.
1 Tacho Conditioning
c
7538
7539 5 Input
1 Generator
Output
7540
7537-A
5 Input
1 Sine Output
BNC
Direct/CCLD
a
1 Tacho Conditioning
c
7538-A
7539-A 5 Input
1 Generator
Output
7540-A
a. Constant Current Line Drive for DeltaTron
®
and ICP
®
Accelerometers or Microphone Preamplifier
b. Using adaptor cables
c. All input channels can be used for tachometer operation
d. Only 12 channels currently supported in PULSE software
e. Upper frequency @ 102.4kHz

BRUEL & KJAER PULSE 3560-C Specifications

General

Brand	BRUEL & KJAER
Model	PULSE 3560-C
Category	Measuring Instruments
Language	English