Cheetah Xi - Default Chapter; Table of Contents

TABLE OF CONTENTS
Cheetah Xi Programming Manual i
P/N: 06-651 Rev 1, 09/2013
TABLE OF CONTENTS
SECTION DESCRIPTION PAGE
1.0 About This Manual ........................................................................................................ 1-1
1.1 About This Manual ........................................................................................................... 1-1
1.2 Product Support ............................................................................................................... 1-1
1.3 Safety Information ........................................................................................................... 1-1
1.4 Related Information ......................................................................................................... 1-2
1.5 Revision History ............................................................................................................... 1-2
2.0 C-Linx Programming Options ...................................................................................... 2-1
2.1 Understanding Cheetah Xi .............................................................................................. 2-1
2.2 Software Programming Features .................................................................................... 2-2
3.0 Getting Started ............................................................................................................... 3-1
3.1 User Interface .................................................................................................................. 3-1
3.2 Password Protection ........................................................................................................ 3-2
3.2.1 How to Log onto the System ........................................................................................... 3-3
3.2.2 Changing the System Administrator Password ............................................................... 3-3
3.3 Configuring the System ................................................................................................... 3-4
3.3.1 Auto-Program .................................................................................................................. 3-4
3.3.2 Engineered Configure ...................................................................................................... 3-4
3.4 How to Address a Device ................................................................................................ 3-5
3.4.1 How to Auto Address Field Devices ................................................................................ 3-5
3.4.2 How to Use the Panel’s Device Address Function .......................................................... 3-6
3.4.3 How to Address Devices with the IR Tool ....................................................................... 3-8
3.4.4 How to Address Devices with the Hand-Held Programmer .......................................... 3-10
3.4.5 How to Address Devices Using C-Linx Device Address Wizard ................................... 3-12
3.4.6 How to Address Devices Using C-Linx Device Address Function ................................ 3-13
4.0 Configuration Menu ....................................................................................................... 4-1
4.1 Configuration Menu ......................................................................................................... 4-1
4.2 Configuration Menu 1 ...................................................................................................... 4-1
4.2.1 How to Configure a Field Device ..................................................................................... 4-1
4.2.1.1 How to Change a Devices Alarm Features ..................................................................... 4-2
A. How to Modify a Sensor ...................................................................................... 4-3
B. How to Modify a Control or Relay Module ........................................................... 4-3
C. How to Modify a Monitor Module ......................................................................... 4-7
D. How to Modify a Pull Station ............................................................................... 4-8
E. How to Delete a Device from the System Configuration ..................................... 4-8
F. How to Read, Write, Enable or Disable a Device ................................................ 4-9
G. How to Set the AHU Relay Re-start Delay ......................................................... 4-10
4.2.1.2 How to Change a Devices Release Features ............................................................... 4-11
4.2.1.3 How to Perform a Configuration Check .........................................................................
4-12
4.2.2 How to Modify the Panel’s NAC Circuits ....................................................................... 4-12
4.2.2.1 How to Modify NAC Functions ...................................................................................... 4-13
4.2.2.2 How to Set NAC Zone Assignments ............................................................................. 4-14
4.2.2.3 How to Set NAC Sync Protocol ..................................................................................... 4-15
4.2.3 How to Change SLC Supervision .................................................................................. 4-15
4.2.3.1 How to Set SLC Command Mode Functions ................................................................. 4-16
4.2.4 How to Execute the Learn Function .............................................................................. 4-17
4.2.4.1 Learn New Devices Only ............................................................................................... 4-17
4.2.4.2 Learn All Devices ........................................................................................................... 4-18
4.3 Configuration Menu 2 .................................................................................................... 4-19
4.3.1 How to Set System Time and Date ............................................................................... 4-19
4.3.2 How to Set System Silencing Options ........................................................................... 4-20
4.3.3 How to Set System Power Options ............................................................................... 4-21