TABLE OF CONTENTS
ii Cheetah Xi Programming Manual
Rev 1, 09/2013 P/N: 06-651
SECTION DESCRIPTION PAGE
4.3.4 How to Modify Daytime Sensitivity Settings ................................................................... 4-22
4.3.4.1 How to Set Daytime Sensitivity Range .......................................................................... 4-22
4.3.4.2 How to Set Holiday Settings for Daytime Sensitivity ...................................................... 4-23
4.3.5 How to Enable/Disable and Assign Custom Messages to Zones .................................. 4-23
4.3.5.1 How to Assign a Chime Code to a Zone ........................................................................ 4-24
4.4 Configuration Menu 3 ..................................................................................................... 4-25
4.4.1 How to Set Peripheral Device Parameters .................................................................... 4-25
4.4.1.1 How to Configure Peripheral Devices ............................................................................ 4-26
4.4.1.1.1 Peripheral Device Testing .............................................................................................. 4-27
4.4.1.1.2 How to Program a 256 LED Graphic ............................................................................. 4-27
4.4.1.2 How to Set the Peripheral Bus Command Source ......................................................... 4-28
4.4.1.3 How to Set the Peripheral Bus Speed ........................................................................... 4-28
4.4.1.4 How to Set the Peripheral Bus Command Set ............................................................... 4-29
4.4.2 How to Enable/Disable System Walktest ....................................................................... 4-30
4.4.3 How to Enable/Disable System Ground Fault Detection ............................................... 4-30
4.4.4 How to Set Panel Abort Type ......................................................................................... 4-31
4.4.5 How to Enable/Disable Day/Night Sensitivity Feature ................................................... 4-32
4.5 Configuration Menu 4 ..................................................................................................... 4-32
4.5.1 How to Set AC Trouble Delay ........................................................................................ 4-33
4.5.2 How to Configure VESDA Detectors .............................................................................. 4-33
4.5.2.1 How to Set VESDA Alarm Features ............................................................................... 4-34
4.5.2.2 How to Set VESDA Sector/Zone Correlation ................................................................. 4-35
4.5.2.3 How to Set VESDA Zone Number and Loop/Addr ........................................................ 4-35
4.5.2.4 How to Set VESDA Release Features ........................................................................... 4-36
4.5.2.5 How to Select VESDA Communication Command Set ................................................... 4-7
4.5.3 How to Configure Auxiliary Power Circuits as AUX/NACs............................................... 4-7
4.5.3.1 How to Set an Auxiliary Power Circuit as an AUX/NAC ................................................ 4-38
4.5.3.2 How to Assign Zones to the AUX/NAC Circuit ............................................................... 4-39
4.5.4 How to Assign Power Cut-Off Relay Address ................................................................ 4-40
4.5.5 How to Configure Panel Relays and Optional Modules ................................................. 4-40
4.5.5.1 How to Set Optional Module Mounting Location ............................................................ 4-41
4.5.5.2 How to Set the Function of the Panel’s
On-Board Relays ............................................. 4-42
4.5.5.3 How to Assign Relays to a Zone .................................................................................... 4-43
4.5.5.4 How to Set Fan Restart Mode ........................................................................................ 4-44
4.6 Configuration Menu 5 ..................................................................................................... 4-44
4.6.1 How to Change System Logo ........................................................................................ 4-45
4.6.2 How to Auto Address Devices ....................................................................................... 4-45
4.6.3 How to Configure Dialer Test ......................................................................................... 4-46
4.6.4 How to Configure Panel Network ................................................................................... 4-46
4.6.4.1 How to Set Panel’s Network ID ...................................................................................... 4-47
4.6.4.2 How to Configure Network Module ................................................................................ 4-49
4.6.4.3 How to Assign Panel to Network Zones ........................................................................ 4-49
4.6.4.4 How to Set the Number of History Repeats ................................................................... 4-50
4.6.4.5 How to Configure Network Switch Functions ................................................................. 4-50
4.7 Configuration Menu 6 ..................................................................................................... 4-51
4.7.1 How to Set Panel’s IP Addresses .................................................................................. 4-51
4.7.1.1 How to Clear Monitoring Panel’s IP Addresses ............................................................. 4-51
4.7.2 How to Configure Panel for Network Supervision .......................................................... 4-52
4.7.3 How to Set IP Time Parameters .................................................................................... 4-53
4.7.4 How to Disable Panel’s Switch Operation ..................................................................... 4-54
4.7.5 How to Set Panel’s LED Operation ................................................................................ 4-54
4.8 Configuration Menu 8 ..................................................................................................... 4-55
4.8.1 How to Enable AHU Key Requirement Feature ............................................................. 4-55
APPENDIX A CyberCat Menu Structure (V6.XX) ............................................................................... A-1
To Next Page
Loading...
