Hoot and Holler over V3PN Configuration Example
Verify
24
OL-6573-01
The following is an output example for the show ip route command, performed using the configuration
on the Headquarters router:
HUB-R1# show ip route
Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP
D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area
N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2
E1 - OSPF external type 1, E2 - OSPF external type 2
i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2
ia - IS-IS inter area, * - candidate default, U - per-user static route
o - ODR, P - periodic downloaded static route
Gateway of last resort is 10.32.152.25 to network 0.0.0.0
192.168.4.0/32 is subnetted, 1 subnets
C 192.168.4.1 is directly connected, Loopback100
O 192.168.5.0/24 [110/11] via 192.168.3.1, 00:12:48, Tunnel0
10.0.0.0/8 is variably subnetted, 2 subnets, 2 masks
C 10.32.152.24/30 is directly connected, ATM1/0
C 192.168.6.0/24 is directly connected, Vif1
O 192.168.7.0/24 [110/11] via 192.168.2.1, 00:12:48, Tunnel1
C 192.168.1.0/24 is directly connected, Vlan10
O 192.168.2.0/24 [110/11] via 192.168.2.1, 00:12:50, Tunnel1
O 192.168.3.0/24 [110/11] via 192.168.3.1, 00:12:50, Tunnel0
S* 0.0.0.0/0 [1/0] via 10.32.152.25
The following is an output example for the show ip pim neighbors command, performed using the
configuration on the Headquarters router:
HUB-R1# show ip pim neighbor
PIM Neighbor Table
Neighbor Interface Uptime/Expires Ver DR
Address Prio/Mode
192.168.3.1 Tunnel0 00:13:52/00:01:40 v2 1 / S
192.168.2.1 Tunnel1 00:13:44/00:01:18 v2 1 / S
The following is an output example for the show ip pim rp map command, performed using the
configuration on the Headquarters router:
HUB-R1# show ip pim rp map
PIM Group-to-RP Mappings
This system is an RP (Auto-RP)
This system is an RP-mapping agent (Loopback100)
Group(s) 224.0.0.0/4
RP 192.168.4.1 (?), v2v1
Info source: 192.168.4.1 (?), elected via Auto-RP
Uptime: 2d02h, expires: 00:02:25
The following is an output example for the show ip mroute active command, performed using the
configuration on the Headquarters router:
HUB-R1# show ip mroute active
Active IP Multicast Sources - sending >= 4 kbps
Group: 239.168.1.100, (?)
Source: 192.168.5.2 (?)
Rate: 0 pps/0 kbps(1sec), 0 kbps(last 0 secs), 2 kbps(life avg)
Source: 192.168.7.2 (?)
Rate: 0 pps/0 kbps(1sec), 80 kbps(last 40 secs), 2 kbps(life avg)
To Next Page
Loading...
Need help?
General
