Danfoss VLT 5000 FLUX User Manual

VLT
®
5000 FLUX
Index
Main Reactance ........................................................... 76
Mains failure
...............................................................105
Mains failure
............................................................... 91
Mains fault
.................................................................107
Mains Interference
........................................................... 8
Mains supply
..............................................................143
Mains supply (L1, L2, L3):
..............................................138
Max motor speed
......................................................... 80
Maximum Inertia
........................................................... 77
Maximum reference
.................................................. 81, 81
Mechanical brake
.......................................................... 85
Mechanical dimensions
.................................................. 14
Mechanical installation
................................................... 17
Menu mode
................................................................ 48
Minimum Intertia
........................................................... 76
Minimum reference
................................................... 80, 80
Minor Interference on Mains
.............................................. 8
Miscellaneous
................................................................ 6
Moment of inertia
.......................................................... 75
Motor
...........................................................................6
Motor cables
............................................................... 38
Motor connection
......................................................... 19
Motor current
.......................................................... 85, 86
Motor current
.............................................................. 63
Motor frequency
........................................................... 70
Motor Parameters
......................................................... 75
Motor power
................................................................ 69
Motor Protection
........................................................9, 19
Motor shaft direction
...................................................... 19
Motor thermal protection
................................................ 19
Motor voltage
............................................................... 64
Multi-references
............................................................ 54
N
Nameplate data....................................................... 69, 70
Normal-constant torque
................................................. 69
Normal/high overload torque control
.................................. 59
O
Operating hours,..........................................................116
Operating mode
..........................................................118
Operation mode
..........................................................118
Output
.........................................................................5
Output speed range/Direction
.......................................... 80
Output speed.
.............................................................. 80
Overvoltage control
......................................................103
P
proportional gain..........................................................106
Parameter groups
......................................................... 48
Parameter setup keys:
................................................... 45
Phase loss
.................................................................. 86
Phase Loss Monitor
....................................................... 86
PLC
........................................................................... 41
Pole number
........................................................... 76, 76
Potentiometer reference
................................................. 37
Power
................................................................... 63, 63
Power monitoring,
........................................................104
Power up
.................................................................... 66
Pre-heat
..................................................................... 73
Pre-magnetizing
........................................................... 72
Preset reference
........................................................... 84
Preset reference, on
...................................................... 90
Programmable Signal Outputs
...........................................8
Programming Setup
...................................................... 62
Pulse reference
....................................................... 64, 91
Pulse start/stop
............................................................ 36
Q
Quick menu mode ........................................................ 47
Quick Menu parameter
................................................... 48
Quick menu, userdefined
................................................ 66
Quick Setup via Quick menu
........................................... 48
Quick stop
.................................................................. 82
Quick-stop
...................................................... 89, 89, 110
R
ramp-up time. .............................................................. 82
Reference
.............................................................. 63, 80
reset
.........................................................................104
Ramp 2
...................................................................... 91
Ramp type
.................................................................. 81
Ramp type,
................................................................. 81
Ramp-down time
..................................................... 81, 81
Ramp-down time.
......................................................... 82
Ramp-up time
.............................................................. 81
Rated motor speed
....................................................... 70
RCD
.......................................................................... 22
Read-outstate
............................................................. 47
Reference
.............................................................. 63, 92
Reference function
........................................................ 83
References
..........................................................6, 83, 84
Relay outputs:
......................................................140, 140
Reset
.................................................................... 89, 89
Reversing
..............................................................90, 111
RFI switch
................................................................... 42
Rotor Leakage Reactance
.............................................. 76
Rotor resistance
........................................................... 75
RS 232
....................................................................... 35
RS 485
....................................................................... 34
S
MG.55.A6.02 - VLT is a registered Danfoss trademark
157

Danfoss VLT 5000 FLUX Specifications

General

Brand	Danfoss
Model	VLT 5000 FLUX
Category	DC Drives
Language	English