Danfoss VLT AutomationDrive FC 301 Operating Guide

Interference isolation..................................................................................20
Isolated mains................................................................................................19
Items supplied...............................................................................................12
K
Knockout......................................................................................................... 18
L
LCP.....................................................................................................................23
Leakage current..................................................................................... 10, 15
Lifting................................................................................................................14
List of warnings and alarms......................................................................44
M
Mains
Mains connection................................................................................19
Warning............................................................................................ 45,51
Mains supply, 200–240 V............................................................. 60, 60, 61
Mains supply, 380–500 V............................................................. 62, 63, 64
Mains supply, 525–600 V............................................................. 65, 65, 66
Mains supply, 525–690 V............................................................. 67, 68, 69
Maintenance.................................................................................................. 43
Mechanical brake control............................................................20, 39, 47
Motor
Thermal protection.............................................................................15
Motor power......................................................................................... 15
Wiring thermistor................................................................................37
Warning.......................................................................... 46,46,50,50,50
Motor cable............................................................................................. 15, 82
Motor output................................................................................................. 71
Motor overload protection..........................................................................6
Motor status......................................................................................................6
Motor terminal.................................................................................................7
Motor wiring.................................................................................................. 20
Mounting.........................................................................................................14
Mounting plate............................................................................................. 14
N
Nameplate...................................................................................................... 12
NEC 2009......................................................................................................... 76
O
Open-loop speed control configurations............................................27
Output power wiring.................................................................................. 21
Output terminal............................................................................................ 22
Overcurrent protection..............................................................................15
P
PELV...................................................................................................................37
Phase imbalance...........................................................................................51
Power factor correction capacitor..........................................................20
Power rating, enclosure size B.................................................................85
Power ratings, enclosure size A...............................................................84
Power ratings, enclosure sizes C and D................................................86
Power wire connection.............................................................................. 15
Pulse input......................................................................................................73
Pulse start/stop wiring configuration................................................... 34
Q
Qualified personnel...................................................................................6, 9
R
Railings.............................................................................................................14
Regen
Wiring configuration..........................................................................37
Relay output...................................................................................................75
Remote commands........................................................................................6
Reset....................................................................................................43, 43, 56
RFI filter............................................................................................................ 19
RS485................................................................................................................ 36
RS485 serial communication....................................................................74
Run/stop command.................................................................................... 32
Run/stop wiring configuration................................................................31
S
Safe Torque Off............................................................................................. 19
See STO
Safe torque off
Wiring of................................................................................................. 33
Service.............................................................................................................. 43
Shielded cable........................................................................................ 18, 21
Shock................................................................................................................ 13
Short circuit
Alarm....................................................................................................... 47
Speed reference............................................................................................27
Start/stop command...................................................................................33
STO...........................................................................17, 19, 56, 56, 56, 57, 72
Storage.............................................................................................................12
Supply voltage.................................................................................19, 22, 70
Surveillance.......................................................................................................6
Switches
Disconnect......................................................................................... 9,43
Symbols.......................................................................................................9, 88
System feedback.............................................................................................6
System set-up................................................................................................ 24
T
Thermal protection........................................................................................ 8
Thermistor
Wiring configuration....................................................................37,37
Warning.................................................................................................. 57
Thermistor control wiring......................................................................... 19
Torque
Warning.................................................................................................. 46
Torque characteristics................................................................................ 71
Trip.....................................................................................................................43
Trip lock............................................................................................................43
Troubleshooting...........................................................................................44
U
UL certification.................................................................................................7
Unintended start......................................................................................9, 43
USB serial communication........................................................................74
V
Vibration..........................................................................................................13
Voltage
Safety warning.......................................................... 9,22,48,50,50,50
Voltage level...................................................................................................72
AQ267037727118en-000101/130R030090 | Danfoss A/S © 2021.01
Index
VLT® AutomationDrive FC 301/FC 302
Operating Guide

Danfoss VLT AutomationDrive FC 301 Specifications

General

Brand	Danfoss
Model	VLT AutomationDrive FC 301
Category	DC Drives
Language	English