DEEP SEA ELECTRONICS DSE4520 - Dse4520 Typical Wiring Diagram (3 Phase 4 Wire)

90 pages

To Next Page

To Previous Page

Installation – Typical Wiring Diagrams

4.2.2 DSE4520 TYPICAL WIRING DIAGRAM (3 PHASE 4 WIRE)

NOTE: Terminals 29-32 are not fitted on the DSE45xx-01 variant.

Main Page

Table of Contents3
Bibliography6
Installation Instructions6
Training Guides6
Manuals6
Third Party Documents6
Introduction7
Specifications8
Short Names8
Operating Temperature8
Requirements for Ul Certification8
Terminal Specification9
Power Supply Requirements9
Module Supply Instrumentation Display9
Voltage & Frequency Sensing10
Current Sensing10
Va Rating of the Cts11
Ct Polarity12
Ct Phasing12
Ct Class12
Inputs13
Digital Inputs13
Analogue Inputs13
Oil Pressure13
Coolant Temperature13
Fuel Level Sensor14
Flexible Sensor (When Configured)14
Charge Fail Input14
Outputs15
DC Outputs a & B (Fuel & Start)15
Configurable DC Outputs C & D15
Configurable DC Outputs E & F (Dse4520 Only)15
Communication Ports15
Communication Port Usage15
Can Interface15
Usb Connection16
Adding an External Sounder17
Accumulated Instrumentation17
Dimensions and Mounting18
Dimensions18
Panel Cutout18
Weight18
Fixing Clips19
Silicon Sealing Gasket20
Applicable Standards21
Enclosure Classifications23
Ip Classifications23
Nema Classifications24
Installation25
Terminal Description25
DC Supply, Fuel and Start Outputs, Outputs C, D, E & F26
Analogue Sensor27
Configurable Digital Inputs & Can28
Generator / Mains Voltage & Frequency Sensing28
Geneator Current Transformers29
Ct Connections29
Pc Configuration Interface Connector30
Typical Wiring Diagram31
Dse4510 Typical Wiring Diagram (3 Phase 4 Wire)32
Dse4520 Typical Wiring Diagram (3 Phase 4 Wire)33
Alternate Topology Wiring Diagrams34
Generator34
Mains (4520 Only)35
Earth Systems36
Negative Earth36
Positive Earth36
Floating Earth36
Description of Controls37
Control Push-Buttons38
Module Display39
Instrumentation Icons40
Active Configuration41
Front Panel Editor (Fpe) / Auto Run Icon41
Mode Icon41
Load Switching Icon42
Backlight42
Alarm Icons (Protections)43
Warning Alarm Icons44
Electrical Trip Alarm Icons45
Shutdown Alarm Icons46
Viewing the Instrument48
Navigation Menu48
Navigation Menu Icons48
General Navigation49
Home50
Generator50
Mains (Dse4520 Only)51
Load51
Engine52
Info52
Engine Dtc (Ecu Alarms)53
Viewing Active Engine Dtc53
Event Log55
Viewing the Event Log55
Operation56
Quickstart Guide56
Starting the Engine56
Stopping the Engine57
Stop/Reset Mode58
Automatic Mode59
Waiting in Auto Mode59
Starting Sequence59
Engine Running59
Stopping Sequence60
Manual/Start Mode61
Waiting in Manual Mode61
Starting Sequence61
Engine Running62
Stopping Sequence62
Maintenance Alarm63
Scheduler64
Stop Mode64
Manual/Start Mode64
Auto Mode64
Front Panel Configuration65
Accessing the Front Panel Configuration Editor66
Adjustable Parameters67
Module Settings67
Can Settings67
Input Settings68
Output Settings69
Timer Settings69
Generator Settings70
Mains Settings71
Engine Settings72
Analogue Inputs Settings73
Scheduler Settings74
Time and Date Settings74
Maintenance Alarm Settings75
Alternate Configuration Settings75
Selectable Parameter Settings77
Input Sources77
Output Sources78
Alarm Action80
Flexible Sensor Alarm Action80
Power up Mode80
Sensor Type80
Ac System80
Digital Input Alarm Arming81
Digital Input Polarity81
Digital Output Polarity81
Fuel Units81
Pressure Sensor List82
Temperature Sensor List82
Percentage Sensor List82
Commissioning83
Fault Finding84
Starting84
Loading84
Alarms85
Communications85
Instruments85
Miscellaneous86
Maintenance, Spares, Repair and Servicing87
Purchasing Additional Connector Plugs from Dse87
Pack of Plugs87
Individual Plugs87
Purchasing Additional Fixing Clips from Dse87
Purchasing Additional Sealing Gasket from Dse87
Warranty88
Disposal88
Weee (Waste Electrical and Electronic Equipment)88
Rohs (Restriction of Hazardous Substances)88

DEEP SEA ELECTRONICS DSE4520 - Dse4520 Typical Wiring Diagram (3 Phase 4 Wire)

Table of Contents

Related product manuals