To Next Page
J
jandersonSep 10, 2025
Why does my Defender Pro Widescreen DVR beep whenever motion is detected?
- BBrian CunninghamSep 10, 2025
The buzzer is set to ON. To disable it, go to ALARM ? MOTION setup and turn the buzzer function OFF.
Why does my Defender Pro Widescreen DVR beep whenever motion is detected?
The buzzer is set to ON. To disable it, go to ALARM ? MOTION setup and turn the buzzer function OFF.
Why does my Defender DVR hard drive fill up so quickly?
A high video quality setting can cause the hard drive to fill up faster. You may want to check your video quality settings and try lowering the video quality. Also, if you are using Schedule Record for 24 hours a day, the hard drive will fill up faster. Try switching periodically to Motion record.
What to do if my Defender DVR mouse is not working?
First, ensure the mouse is connected to the top USB port on the back of the DVR. If it still doesn't work, try connecting the mouse to a different USB port to ensure it is not defective.
Why does my Defender DVR keep beeping?
The DVR may be beeping due to video loss, HDD loss, motion detection, or lack of HDD space. Check your connections and ensure the DVR is in a safe place. You can also try disconnecting and reconnecting all camera connections to make sure they are snug and tight fitting.
What to do if my Defender DVR remote control is not working?
First, ensure the batteries are installed correctly. Then, make sure you are pointing the remote at the IR sensor. Point the IR Remote at the camera lens and press a button. You should be able to see the IR LED flicker through the DVR monitoring device. If it still doesn’t work, try replacing the batteries in the remote.
How to fix Defender Pro Widescreen DVR when nothing is recording, but all the images are appearing on the screen?
To start recording, press the RECORD button on the remote. Also, go to RECORD ? REC PARA ? RECORD to ensure all cameras are set to ENABLE. Check your record schedule to ensure the DVR is set to record that hour. Verify that the HDD is installed and formatted in the DEVICE menu.
Why is the HDD light blinking on my Defender Pro Widescreen?
If the hard drive is playing back footage or recording, the light will blink to notify you that there is activity.
How to fix Defender Pro Widescreen DVR when it is not recording according to my schedule?
Check to see if you have the proper time set on your DVR. Also, check your schedule record times as you may have the DVR set to "no record".
How to fix Defender Pro Widescreen DVR if I cannot view online footage using my external IP address?
Sometimes your router will not allow you to view the footage with your external IP address because the DVR is connected to the same router. Try typing the DVR's internal IP address in the address bar. If using a port other than 80, add your port forwarded port to the end of the IP address.
How to fix Defender Pro Widescreen DVR when I cannot power it off?
The DVR is set to run as long as it is plugged in. To power off the DVR, go to ADVANCED ? SHUT DOWN. After that, disconnect the power cable once you see "YOU CAN UNPLUG THE POWER".
Details the terms and conditions of the product warranty.
Steps to power on the DVR and initiate its startup sequence.
Configuration options for camera display settings and properties.
Setting up and managing recording parameters for the DVR.
How to search and retrieve recorded footage by date and time.
Configuring network settings for online viewing and remote access.
Configuring DVR alarm triggers and notification settings.
Methods to locate and identify the DVR's IP address on the network.
Configuring the computer for remote DVR access, including ActiveX controls.
Accessing the DVR's live feed and recordings via a computer.
Setting up remote viewing from external locations.
Installing and utilizing the remote viewing setup software.
Configuring DVR settings for mobile access.
Troubleshooting remote Internet connection problems for DVR access.
General| Video Input | 4 channels |
|---|---|
| Hard Drive Support | 1 SATA HDD |
| Operating System | Embedded Linux |
| Compression | H.264 |
| Remote Viewing | Yes |
| Power Supply | 12V DC |
| Video Output | HDMI, VGA |
| Audio Input | 4 channels |
| Audio Output | 1 channel |
| Recording Frame Rate | 30 fps |
| Remote Access | Yes |
| Motion Detection | Yes |
| Operating System Compatibility | Windows, iOS, Android |