ENGLISH
Select HDMI audio output device.
[Selectable
items]
I
AMP
I:
Use speakers connected to receiver for audio playback.
TV :Use speakers
of
monitor for audio playback.
HOMI
Audio
Out
~AMP~
2-2.HOMI
Setup
1.
Speaker
Setup
[1'2. HOMI
Setup
3.Audio
Setup
4.
Zone2
Setup
S.Option
Setup
HDMI
Audio
Out
Set the crossover frequency separately for the different speakers.
[Selectable
items]
40Hz
60Hz
I
80Hz
I
90Hz
10l)Hz
110Hz
120Hz
150Hz
200Hz
250Hz
Only the portion
of
the bass sound
of
the various speakers output
from the subwoofer that has a frequency below the frequency set
here
is
output.
Set this according to the
low
frequency reproduction capabilities
of
the
speakers you are using.
Advanced
• When the menu "Speaker Configuration"
-"
Surround Back Speaker"
setting
(!3f'page
24)
is set to
"1
spkr'; the surround back speaker
display
is
set to "Surround
Back
Sp."
.
• Speakers set to
"None"
in
the"
Speaker Configuration" settings
are
not displayed.
• When "Channel Level"
is
adjusted, the adjusted values are set for
all
the surround modes.
To
adjust the channel level separately for the
different surround modes, use the operation see page 46.
• The "Crossover Frequency"
can
be set when there are speakers that
have been set to "Small" at menu "Speaker Configuration" or when
"Subwoofer"
is
set to "Yes" (!3f'page 24).
·If
menu "Subwoofer Setup"
(!3f'page
24)
is
set
to
"LFE'; speakers
set to "Small" at "Speaker Configuration" can be set. If set
to
"LFE+Main'; this
can
be set regardless
of
the size
of
the speaker.
•
For
speakers set to "Small'; sound below the crossover frequency
is
cut from the sound output. The cut bass sound
is
output from the
subwoofer or front speakers.
• Always set the crossover frequency to
"80
Hz': When using small
speakers, however,
we
recommend setting the crossover frequency
to a higher frequency.
i~'.
Crossover Frequency
Select crossover frequency from which subwoofer handles
low
range signal.
:Display when
"Feet"
is
set.
: Display
when"
Meters"
is
set.
TestTone
Distance
measurement
.Chann~1
Level ,
;~
" . ,
Adjllst
channel levels
to
.Qb,tBin
eQual
volume.from all speilk,ers.
TestTone
Start
-N·Ua
Set the distance between the listening position and the various
speakers to no more than 20.0 ft (6.00 meters).
Default
Resets the settings to the default values.
[Variable range]
Select the speaker you want to set, then set the distance.
Set the value closest to the measured distance.
Output
test
tone.
[Variable range]
...;.12dB
- I
OdB
I-
+12dB
_•
Operating
from
the
main
remote
control
unit
Adjusting
with
the main remote control unit using the test tones
is
only possible
in
the "Auto" mode and only effective in the STANDARD
mode. The adjusted levels for the different modes are automatically
stored
in
the memory.
[Adjusting using
test
tonesl
CD
Press the
TEST
button.
Test tones are output from the various speakers.
® Use the
~
t>
button to adjust so that the volume
is
equal for
all
speakers.
@ When the adjustments
are
completed, press the
TEST
button
again.
Select
test
tone playback method.
[Selectable
items]
I
Auto
I:
Automatically switch speaker from which test tone
is
output.
Manual
: Manually switch speaker from which test tone
is
output.
:rJ
til
3
o
"
C"l
o
~
2.
•
25
To Next Page
Loading...
