ENGLISH
f"G)
I
~
I
:;'
I <0
I
~
.
.,
i
~
L.::..
I
(")
I g
I
;;
j
~
!
o'
I
~
I 5
I "
I
~
i
~
£.
r--
I S
I t
IT
i
g'
r-;-
I
~
. "
I
U>
I
g-
I
~
I
~.
• With the default settings, the
iPod
can
be
used connected to the
VCR
(iPod)
connector.
• Use the
RESTORER
mode to expand the low
and
high frequency
components of compressed audio files
and
achieve a richer sound.
The
default setting
is
"Mode3':
• Press
<ON/STANDBY>
and
set the AVR-1908's power to the standby
mode before disconnecting the
iPod.
Also switch the input source
to one to which the menu "iPod dock"
is
not assigned before
disconnecting the
iPod.
-NeI'.
• Depending
on
the type of
iPod
and
the software version, some
functions may not operate.
• DENON will accept
no
responsibility whatsoever for
any
loss
of
iPod
data.
iPod® Playback
The
musIc
on
an
IPod
can
be
played
by
USing
the Control
Dock
for
IPod
IASD-l
R,
sCld
separately)
The
operation
can
also
be
performed
uSing
the buttons
on
the main
unit or remote control unit while watching the menus
MENU:
"Input
Setup"
-
"Assign"
- "iPod dock"
(~page
33)
Basic
·Operiltior(
(iPod
screen)
*If the screens above
are
not displayed, the
iPod
may
not
be
properly connected.
Try
connecting again.
1Make the necessary preparations.
CDSet
the
iPod
in
the DENON Control Dock for
iPod.
(~See
the Control Dock for iPod's operating instructions.)
®Assign
the Control Dock for iPod's input.
iPod
is a trademark of Apple Inc., registered
in
the
U.S.
and
other countries.
*
The
iPod
may only
be
used to copy or play contents that
are
not
copyrighted or contents for which copying or playback
is
legally
permitted for your private
use
as
an
individual.
Be
sure to comply
with applicable copyright legislation.
2
Either tum
<SOURCE
SELECT>
or press
[iPod]
to
select the input source assigned in step
l-CV
above.
3
Set
[MODE
SELECTOR
1]
to "AUDIO" and
[MODE
SELECTOR
2]
to ''iPod/NETWORK''.
(~page
48 "Remote Control Unit Operations")
GOOD Signal strength
is
good
MARGINAL
Signal strength
is
marginal
WEAK
Signal strength
is
weak
NO
No signal
L-,:CJ::
H!j'
T~:~JF.~.:
'~:":=":'k
~4===:j1-
Channel category
1
Either turn
<SOURCE
SELECT>
or press
[SAT
TU]
to
select
''XM''.
2
Press
STATUS
until ''SIGNAL'' appears on the
display.
The
display
will
switch
as
shown below, depending
on
the
reception conditions.
The strength of both the XM satellite and terrestrial signals
can
be
checked at menu "Input Setup" - "Antenna Aiming"
(!l2U'page
34).
4
Press
STATUS
until the station you want to check
(example:
''XMOOl'')
is displayed.
3
Adjust the position
of
the antenna until "SIGNAL:
GOOD" is shown on the display.
5
Press
TUNING
and select channel 0
(XMOOO).
The
radio
ID
is
shown
on
the display.
1>,;['1000 PADIO ID
dRadiolD
2
Use
<J
t>
to select the category, then use
D.
V
to
select
the desired station.
44
To Next Page
Loading...
Need help?
General
