ENGLISH
s
c:
tt
N
o
:J
l1)
I
Troubleshooting
If a problem should arise. first check
the
following:
1.
Are
the
connections correct?
2. Is
the
set being operated as described
in
the
owner's manual?
3. Are
the
other components operating properly?
If this unit does not operate properly, check the items listed
in
the table below. Should the problem persist,
there may
be
a malfunction.
In
this case, disconnect the power immediately
and
contact your store of purchase.
[General]
Symptom
....
"[,-1:."
<.~/
Cause
Countenneasure
~
Page
Power does not
• Connection of the power cord
is
• Check the insertion of the power
17
turn on, or turns faulty. cord plug.
off directly after it
was turned
on.
No
sound
is
• Connection
with the input
• Check the connections.
9
produced from devices or connection of the
speakers. speaker cables
is
faulty.
• Device you want to play
and
set
• Select
an
appropriate input
41
input source do not match.
source.
• Master
volume
is
turned
too • Adjust the master volume to
an
41
low. appropriate level.
• Mute mode
is
set.
• Cancel the mute mode.
41
• Headphones
are
connected.
• Disconnect the headphones.
41
•
No
digital signals
are
being
• Select
an
input source for which
33
input. the digital input setting
has
been
made.
·The
connectors
to which
the
• Set the input mode.
32
digital inputs
are
assigned
and
the settable input modes do not
match.
Display
is
off.
•
The
"Dimmer"
setting
is
set to
• Set
to
something
other
than
30
"OFF': "OFF':
•
The
PURE
DIRECT
mode
is
set. • Set a surround mode other than 35
the
PURE
DIRECT
mode.
"DOLBY
DIGITAL:'
•
DVD
player's digital audio output
•
Check
the
DVD
player's audio -
indicator does not
setting
is
not proper.
output setting.
For
details,
read
appear
on
display.
the
DVD
player's
operating
instructions.
Symptom
,.
Cause
Countenneasure
Page
Power turns off • Protection circuit activated due
•
Turn
off the power, wait for the
10
suddenly
and
to rise of internal temperature.
set to fully cool down, then turn
power indicator
the power
back
on.-
flashes
red.
•
Place
the set
in
a well-ventilated
10
place.
• Core wires of
two
speakers are
• First
unplug the
power cord,
10
touching
each
other or a core
then
twist
the core wires tightly
wire
is
sticking out of the terminal
or terminate the speaker cables,
and
touching the set's
rear
panel,
then reconnect.
activating the protection circuit.
• Speakers
with
an
impedance • Use speakers with the specified
10
other than specified
are
being impedance.
used.
• Set
is
damaged.
•
Turn
off the power
and
contact a
-
DENON
service center.
[Remote Control Unit]
"
.~F'
~!r,.*",
.fCause ;'/'0'
~~
'n
Countermeasure
"
,.
Page
Set does not work
• Batteries
are
worn.
•
Replace
with new batteries.
3
properly when
•
You
are
operating outside of the
• Operate
within the specified 3
remote control
specified
range.
range.
unit operated.
• Obstacle between main unit
and
• Remove the obstacle.
3
remote control unit.
•
The
batteries
are
not inserted
in
• Insert
the
batteries
in
the 3
the proper direction,
as
indicated
proper direction, following the
by
the polarity marks
in
the
polarity marks
in
the
battery
battery compartment.
compartment.
•
The
set's remote control sensor
• Move the set to a place
in
which
3
is
exposed to strong light (direct
the remote control sensor will
sunlight, invertertype fluorescent
not
be
exposed to strong light.
bulb light, etc.).
•
The
remote
ID
of the main unit
• Set Remote
ID
for the main unit
30
and
remote control unit do not
to "1':
match.
65
To Next Page
Loading...
