Dish Network Smartbox - Page 54

Dish Network Smartbox

74 pages

Save Page as PDF

To Next Page

To Next Page

To Previous Page

To Previous Page

Loading...

54

Figure 35. DISH QAM Conﬁguration Tab

Table of Contents

Default Chapter3
- Table of Contents3
- Important Safety Information5
CHAPTER 1 Introduction to SMARTBOX8
- Site Requirements8
- Installation Overview9
CHAPTER 2 Assemble Chassis, Power Supplies, and Power Inserters10
- Install Chassis and Power Supplies10
- Mount Power Inserter and Connect Input/Output Cables to Power Inserter11
- DISH 4-Port High-Capacity Power Inserter11
CHAPTER 3 Install Blades12
- Plan Distribution of Blades12
- Inspect Blades13
- Install the Blades and Filler Plates13
CHAPTER 4 Update Software14
- Configure Computer Network Settings14
- Establish Communication with SMARTBOX16
- Connect Cables to Connectors and Install Cellular Antenna16
- Login to SMARTBOX17
- Admin Tab18
- Chassis Tab18
- Enable Satellite Inputs19
- Verify Tuners Lock20
- Download Software from Satellite21
- Update Settings for Automatic Update21
- Download Software from SFTP21
- Manually Update Software22
CHAPTER 5 Feature-Enabling Codes23
CHAPTER 6 Authorize SMARTBOX24
- Authorization - 10025
- Authorization - Less than 10026
- Authorization Page27
CHAPTER 7 Scan for Spot Beams and Satellite Services28
CHAPTER 8 Specify Data Port-Content/Control Interface29
CHAPTER 9 ATSC Installation30
- ATSC Input Signal Characteristics30
- ATSC GUI Interface33
CHAPTER 10 Set up CAS Server34
CHAPTER 11 Map Services35
- Configuration File36
- Configure Services36
- Encrypted QAM Output37
- HD over Coax Output37
- NTSC Output37
- Max Services Per QAM Channel38
- Encrypted IP Stream Output38
- Quick Add39
- IP Input (Welcome Channel)39
- General Requirements39
- IP Packet Details39
- Transport Stream Format40
- Pids40
- Timing/Pcrs40
- Continuous Video and Audio40
- Adding the IP Input Service(S)41
- Add Monroe R189 EAS (Emergency Alert System)42
- Part-Time HD Alternate Display (RSN)42
CHAPTER 12 Set up a Program Guide43
- Configure Program Guide Output Options43
- Configure Update Time for the Guide Channel44
- Adding External Services to the Program Guide45
CHAPTER 13 Evolve Configuration46
- Set up the DVB-SI Service47
- Adding Additional Files47
- Replacing Existing Files49
- Set up ATSC for EVOLVE49
- Set Zones for Services51
- NOTE-Nuances to Feeding Video to Non-EVOLVE Devices52
Dish Qam Operational Mode, Ch53
Chapter 14 Dish Qam53
- Set up DISH QAM53
- Validate DISH QAM Status55
CHAPTER 15 Manual Factory Default56
- Factory Default Without Access to User Interface56
CHAPTER 16 Soak Test and Prepare to Ship57
- Soak Test57
- Prepare to Ship57
CHAPTER 17 Install on Customer Site58
CHAPTER 18 Status, Warnings, and Faults59
CHAPTER 19 Diagnostic Information60
- ATSC Receiver Blades60
- Satellite Receiver Blades60
CHAPTER 20 LED Information61
- LED Definitions for Satellite Feeds61
- LED Definitions for Blades61
- LED Definitions for Cellular Antennas61
Chapter 21 Ntsc Channel-Frequency62
CHAPTER 22 Hardware Components63
- 16-Slot Chassis63
- 8-Channel Satellite Receiver Blade63
- 8-Channel Satellite Receiver Blade with Transcoder Module63
- 8-Channel ATSC Receiver Blade63
- QAM 16 Blade63
- QAM 48 Blade63
- QAM 96 Blade63
- 24-Channel Analog NTSC TV Blade63
- Power Supply63
CHAPTER 23 Technical Specifications64
- Power Consumption64
- Chassis Assembly64
- Chassis Assembly Specifications65
- Satellite Receiver Blade65
- Power Supply Module67
- LED Status67
- Satellite Receiver Blade68
- Satellite Receiver Blade with Transcoder Module68
- ATSC Receiver Blade68
- QAM 16 Blade69
- QAM16 Blade69
- QAM 48 Blade69
- QAM48 Blade69
- QAM 96 Blade70
- QAM96 Blade70
- NTSC 24 Blade70
- Tolerances and Ranges71
CHAPTER 24 Warranty Information and Return Authorization72
CHAPTER 25 Trademark Acknowledgements72
CHAPTER 26 Technical Support and Authorization Assistance72
Regulatory Compliance73