Dish Network Smartbox - Page 74

Dish Network Smartbox

74 pages

Save Page as PDF

To Previous Page

To Previous Page

Loading...

74

Table of Contents

Default Chapter3
- Table of Contents3
- Important Safety Information5
CHAPTER 1 Introduction to SMARTBOX8
- Site Requirements8
- Installation Overview9
CHAPTER 2 Assemble Chassis, Power Supplies, and Power Inserters10
- Install Chassis and Power Supplies10
- Mount Power Inserter and Connect Input/Output Cables to Power Inserter11
- DISH 4-Port High-Capacity Power Inserter11
CHAPTER 3 Install Blades12
- Plan Distribution of Blades12
- Inspect Blades13
- Install the Blades and Filler Plates13
CHAPTER 4 Update Software14
- Configure Computer Network Settings14
- Establish Communication with SMARTBOX16
- Connect Cables to Connectors and Install Cellular Antenna16
- Login to SMARTBOX17
- Admin Tab18
- Chassis Tab18
- Enable Satellite Inputs19
- Verify Tuners Lock20
- Download Software from Satellite21
- Update Settings for Automatic Update21
- Download Software from SFTP21
- Manually Update Software22
CHAPTER 5 Feature-Enabling Codes23
CHAPTER 6 Authorize SMARTBOX24
- Authorization - 10025
- Authorization - Less than 10026
- Authorization Page27
CHAPTER 7 Scan for Spot Beams and Satellite Services28
CHAPTER 8 Specify Data Port-Content/Control Interface29
CHAPTER 9 ATSC Installation30
- ATSC Input Signal Characteristics30
- ATSC GUI Interface33
CHAPTER 10 Set up CAS Server34
CHAPTER 11 Map Services35
- Configuration File36
- Configure Services36
- Encrypted QAM Output37
- HD over Coax Output37
- NTSC Output37
- Max Services Per QAM Channel38
- Encrypted IP Stream Output38
- Quick Add39
- IP Input (Welcome Channel)39
- General Requirements39
- IP Packet Details39
- Transport Stream Format40
- Pids40
- Timing/Pcrs40
- Continuous Video and Audio40
- Adding the IP Input Service(S)41
- Add Monroe R189 EAS (Emergency Alert System)42
- Part-Time HD Alternate Display (RSN)42
CHAPTER 12 Set up a Program Guide43
- Configure Program Guide Output Options43
- Configure Update Time for the Guide Channel44
- Adding External Services to the Program Guide45
CHAPTER 13 Evolve Configuration46
- Set up the DVB-SI Service47
- Adding Additional Files47
- Replacing Existing Files49
- Set up ATSC for EVOLVE49
- Set Zones for Services51
- NOTE-Nuances to Feeding Video to Non-EVOLVE Devices52
Dish Qam Operational Mode, Ch53
Chapter 14 Dish Qam53
- Set up DISH QAM53
- Validate DISH QAM Status55
CHAPTER 15 Manual Factory Default56
- Factory Default Without Access to User Interface56
CHAPTER 16 Soak Test and Prepare to Ship57
- Soak Test57
- Prepare to Ship57
CHAPTER 17 Install on Customer Site58
CHAPTER 18 Status, Warnings, and Faults59
CHAPTER 19 Diagnostic Information60
- ATSC Receiver Blades60
- Satellite Receiver Blades60
CHAPTER 20 LED Information61
- LED Definitions for Satellite Feeds61
- LED Definitions for Blades61
- LED Definitions for Cellular Antennas61
Chapter 21 Ntsc Channel-Frequency62
CHAPTER 22 Hardware Components63
- 16-Slot Chassis63
- 8-Channel Satellite Receiver Blade63
- 8-Channel Satellite Receiver Blade with Transcoder Module63
- 8-Channel ATSC Receiver Blade63
- QAM 16 Blade63
- QAM 48 Blade63
- QAM 96 Blade63
- 24-Channel Analog NTSC TV Blade63
- Power Supply63
CHAPTER 23 Technical Specifications64
- Power Consumption64
- Chassis Assembly64
- Chassis Assembly Specifications65
- Satellite Receiver Blade65
- Power Supply Module67
- LED Status67
- Satellite Receiver Blade68
- Satellite Receiver Blade with Transcoder Module68
- ATSC Receiver Blade68
- QAM 16 Blade69
- QAM16 Blade69
- QAM 48 Blade69
- QAM48 Blade69
- QAM 96 Blade70
- QAM96 Blade70
- NTSC 24 Blade70
- Tolerances and Ranges71
CHAPTER 24 Warranty Information and Return Authorization72
CHAPTER 25 Trademark Acknowledgements72
CHAPTER 26 Technical Support and Authorization Assistance72
Regulatory Compliance73