To Next Page
J
James SmithSep 9, 2025
What does "Err EP" EEPROM error mean on Doran 7000?
- JjoelmarquezSep 9, 2025
The nonvolatile memory has been corrupted by transients or electrostatic discharge. Reenter the scale parameters and recalibrate the Doran scale.
What does "Err EP" EEPROM error mean on Doran 7000?
The nonvolatile memory has been corrupted by transients or electrostatic discharge. Reenter the scale parameters and recalibrate the Doran scale.
What does "Ldg 0" Loading zero mean on my Doran 7000?
The Doran scale is attempting to load power up zero. This message will remain until the scale is stable.
Why won't my Doran 7000 indicate full capacity?
Make sure there is nothing caught in the platform under or around the load cell or spider interfering with its movement. If not, check the overload stops using the procedure described above.
What does "rg. Err" Calibration range error mean on Doran 7000 Scales?
Press ZERO to clear the error on your Doran scale. Then correct the input levels.
Why do my Doran 7000 Scales overload early?
Make sure all four overload stops are properly set on your Doran scale. Remove the platter, invert it, and place it back on the spider. With 1/2 of the scale's capacity in test weights concentrated over a corner of the platform, there should be approximately 1/32" of clearance between the stop and the bottom of the spider. Check all four corners, then recalibrate the scale. If the problem persists, the scale may be shock-loaded, causing the load cell to shift. Review the cautions in section 1.
Lists common features like NTEP certification, display, units, RS232, and load cell support.
Highlights unique features of the 7000XL model, such as its touch panel and indicators.
Step-by-step guide for performing basic weighing tasks on the 7000XL.
Instructions on how to switch between different weight units (lb, kg, oz, g).
Procedure for sending weight data to a printer or external device.
Steps for basic weighing on the Model 7000 scale.
Instructions on how to switch between different weight units.
Procedure for sending weight data to a printer or external device.
Safety instructions and precautions for safely removing the scale from its packaging.
Guidance on physically mounting the scale indicator in a desired location.
Details on how to connect the scale to a power source and power quality considerations.
Description of the operational controls and display elements specific to the 7000XL.
Description of the operational controls and display elements specific to the Model 7000.
Explanation of the ZERO, UNITS, and PRINT buttons' functions and behavior.
Information on connecting load cells and external option interfaces.
Procedures for setting scale capacity and performing calibration.
Guides for entering/exiting setup, navigating menus, changing parameters, and reviewing settings.
Information on limitations and settings specific to Legal for Trade compliance.
Menu for selecting the scale's maximum weighing capacity.
Configuration options for digital filtering and automatic zero tracking.
Configuration for zero/print latching and printer data output modes.
Settings for data formats, baud rate, and front panel/remote switch functions.
General steps for performing digital calibration of the scale.
Method for adjusting the scale's zero and span calibration points.
Instructions for setting scale type and power jumpers.
Details on jumpers affecting zero shift and span adjustment.
Introduction to asynchronous serial communications and ASCII codes.
Explanation of baud rate, start/stop bits, and parity.
Description of different print control modes (tod, CP, AP1, AP2).
Overview of available data formatting options for serial output.
Detailed explanation of the standard F0 data output format.
Explanation of the dual print format for kg equivalent output.
Details on F1, SSP, and DGH formats for compatibility and special outputs.
Technical specifications for Model 7000 and 7000XL scales.
General information on connectors and pin assignments.
Pinout and connection details for the TB1 load cell connector.
Details for P2 options, J1 power, and P3/P3B keyboard connectors.
Information on constructing serial cables with hardware handshaking.
General steps and checks for resolving common scale problems.
Troubleshooting steps for when the scale overloads prematurely.
Solutions for issues like incorrect readings, zero drift, and bouncing scales.
Procedures for resetting scale parameters to factory defaults or power cycling.
Explains common error messages and how to resolve them.
General
