DURKOPP ADLER 827 User Manual

6 Electrical connection
6.1 General
Caution !
All work on the electrical equipment of this special sewing
machine may only be carried out by qualified electricians or
other appropriately trained persons.
The mains plug must be removed.
6.2 Checking the mains voltage
Caution !
The mains voltage must agree with the rated voltage specified
on the model-identification plate.
6.3 Connecting the sewing drive
6.3.1 Connecting the clutch motor
–
Lay the connection cable from the main switch through the cable
conduit to the sewing drive and connect it to the sewing drive. See
connection diagram 9800 169002 B (in the connection pack) or the
circuit diagram on the clutch motor.
–
Lay the mains cable from the main switch back through the cable
conduit and attach to the mains-lead cleat.
6.3.2 Connecting the coupling-positioning actuator
–
Lay the connection cable from the motor-protection switch
through the cable conduit to the sewing drive and connect it to the
sewing drive.
See connection diagram 9800 129002 B (in the connection pack)
or the circuit diagram on the coupling-positioning actuator.
–
Lay the mains cable from the main switch back through the cable
conduit and attach to the mains-lead cleat.
–
Plug the cable from the set-point generator into socket b80 of the
drive control. See figure page 20.
6.3.3 Connecting the direct-current positioning actuator
–
Lay the connection cable from the main switch through the cable
conduit to the sewing drive and connect it to the sewing drive. See
connection diagram 9800 139001 B (in the connection pack).
–
Lay the mains cable from the main switch back through the cable
conduit and attach to the mains-lead cleat.
–
Plug the lead from the set-point generator into socket b80 of the
drive control. See figure page 20.
14
6 Electrical connection
6.1 General
Caution !
All work on the electrical equipment of this special sewing
machine may only be carried out by qualified electricians or
other appropriately trained persons.
The mains plug must be removed.
6.2 Checking the mains voltage
Caution !
The mains voltage must agree with the rated voltage specified
on the model-identification plate.
6.3 Connecting the sewing drive
6.3.1 Connecting the clutch motor
–
Lay the connection cable from the main switch through the cable
conduit to the sewing drive and connect it to the sewing drive. See
connection diagram 9800 169002 B (in the connection pack) or the
circuit diagram on the clutch motor.
–
Lay the mains cable from the main switch back through the cable
conduit and attach to the mains-lead cleat.
6.3.2 Connecting the coupling-positioning actuator
–
Lay the connection cable from the motor-protection switch
through the cable conduit to the sewing drive and connect it to the
sewing drive.
See connection diagram 9800 129002 B (in the connection pack)
or the circuit diagram on the coupling-positioning actuator.
–
Lay the mains cable from the main switch back through the cable
conduit and attach to the mains-lead cleat.
–
Plug the cable from the set-point generator into socket b80 of the
drive control. See figure page 20.
6.3.3 Connecting the direct-current positioning actuator
–
Lay the connection cable from the main switch through the cable
conduit to the sewing drive and connect it to the sewing drive. See
connection diagram 9800 139001 B (in the connection pack).
–
Lay the mains cable from the main switch back through the cable
conduit and attach to the mains-lead cleat.
–
Plug the lead from the set-point generator into socket b80 of the
drive control. See figure page 20.
14
6 Electrical connection
6.1 General
Caution !
All work on the electrical equipment of this special sewing
machine may only be carried out by qualified electricians or
other appropriately trained persons.
The mains plug must be removed.
6.2 Checking the mains voltage
Caution !
The mains voltage must agree with the rated voltage specified
on the model-identification plate.
6.3 Connecting the sewing drive
6.3.1 Connecting the clutch motor
–
Lay the connection cable from the main switch through the cable
conduit to the sewing drive and connect it to the sewing drive. See
connection diagram 9800 169002 B (in the connection pack) or the
circuit diagram on the clutch motor.
–
Lay the mains cable from the main switch back through the cable
conduit and attach to the mains-lead cleat.
6.3.2 Connecting the coupling-positioning actuator
–
Lay the connection cable from the motor-protection switch
through the cable conduit to the sewing drive and connect it to the
sewing drive.
See connection diagram 9800 129002 B (in the connection pack)
or the circuit diagram on the coupling-positioning actuator.
–
Lay the mains cable from the main switch back through the cable
conduit and attach to the mains-lead cleat.
–
Plug the cable from the set-point generator into socket b80 of the
drive control. See figure page 20.
6.3.3 Connecting the direct-current positioning actuator
–
Lay the connection cable from the main switch through the cable
conduit to the sewing drive and connect it to the sewing drive. See
connection diagram 9800 139001 B (in the connection pack).
–
Lay the mains cable from the main switch back through the cable
conduit and attach to the mains-lead cleat.
–
Plug the lead from the set-point generator into socket b80 of the
drive control. See figure page 20.
14
6 Electrical connection
6.1 General
Caution !
All work on the electrical equipment of this special sewing
machine may only be carried out by qualified electricians or
other appropriately trained persons.
The mains plug must be removed.
6.2 Checking the mains voltage
Caution !
The mains voltage must agree with the rated voltage specified
on the model-identification plate.
6.3 Connecting the sewing drive
6.3.1 Connecting the clutch motor
–
Lay the connection cable from the main switch through the cable
conduit to the sewing drive and connect it to the sewing drive. See
connection diagram 9800 169002 B (in the connection pack) or the
circuit diagram on the clutch motor.
–
Lay the mains cable from the main switch back through the cable
conduit and attach to the mains-lead cleat.
6.3.2 Connecting the coupling-positioning actuator
–
Lay the connection cable from the motor-protection switch
through the cable conduit to the sewing drive and connect it to the
sewing drive.
See connection diagram 9800 129002 B (in the connection pack)
or the circuit diagram on the coupling-positioning actuator.
–
Lay the mains cable from the main switch back through the cable
conduit and attach to the mains-lead cleat.
–
Plug the cable from the set-point generator into socket b80 of the
drive control. See figure page 20.
6.3.3 Connecting the direct-current positioning actuator
–
Lay the connection cable from the main switch through the cable
conduit to the sewing drive and connect it to the sewing drive. See
connection diagram 9800 139001 B (in the connection pack).
–
Lay the mains cable from the main switch back through the cable
conduit and attach to the mains-lead cleat.
–
Plug the lead from the set-point generator into socket b80 of the
drive control. See figure page 20.
14

DURKOPP ADLER 827 Specifications

General

Brand	DURKOPP ADLER
Model	827
Category	Sewing Machine
Language	English