Calibration Methods55
- Dry Calibration55
- Figure 5-1 Calibration - Meter Factors Page56
- Table 5-1 Data Points for Dry Calibration57
- Wet Calibration59
- Table 5-2 Data Points for Wet Calibration Method59
- Wet Calibration Piece-Wise Linearization60
- Figure 5-2 Calibration - Meter Factor: None60
- Figure 5-3 Calibration - Meter Factor: Piecewise Linearization61
- Table 5-3 Data Points for Piece-Wise Linearization Calibration62
- Third-Order Polynomial63
- Figure 5-4 Calibration - Meter Factor: Polynomial63
- Table 5-4 Data Points for Polynomial Wet Calibration64
- No Wet Calibration65
- Triggered Delta Volumes65
- Table 5-5 Configure Operational Parameters66
Calibrate Analog Inputs and Outputs68
Figure 5-5 Offset Calibration69
Calibrate Meter Factors71
- Flow Calibration71
- Figure 5-6 Gating Configuration Parameter Edge Gated, Active High71
- Figure 5-7 Gating Configuration Parameter Edge Gated, Active Low72
- Figure 5-8 Gating Configuration Parameter State Gated, Active High72
- Figure 5-9 Gating Configuration Parameter State Gated, Active Low72
- Configure Frequency/Digital Output Sources73
- Table 5-6 Frequency/Digital Outputs Possible Configurations74
- Figure 5-10 CPU Module - Frequency/Digital Outputs Common Ground75
- Figure 5-11 CPU Module - Frequency/Digital Outputs Common Ground - Type 476
Configure Frequency Outputs77
Configure Digital Input/Outputs79
Figure 5-12 Meter Outputs Test Page80
Outputs Test Mode80
Configure HART Outputs81
- Configure the Four Dynamic Variables81
- Configure the Device Identification82
- Configure the HART Units82
Configure Meter Corrections82
- Flow Profile Correction82
- Temperature Expansion Correction82
- Pressure Expansion Correction82
Configure Temperature and Pressure83
- Flow-Condition Pressure and Temperature83
- Table 5-7 Flow-Condition Pressure and Temperature Data Source84
- Configure the Temperature Parameters for the Meter85
- Configure the Pressure Parameters for the Meter85
Configure Gas Chromatograph Parameters86
- Gas Properties87
- Table 5-8 Fixed Gas Composition Data Points88
- Table 5-9 GC-Reported Gas Composition Data Points89
- Table 5-10 In-Use Gas Composition Data Points90
Table 5-11 C6+ Breakdown to Standard Components by Component ID91
Table 5-12 Gas Chromatograph Sim 2251 Registers92
Table 5-13 Supported Component Ids93
Data Polling94
Gas Property Data94
Table 5-14 GC Communication Status List94
GC Alarm Handling95
GC Data Validity95
Table 5-15 GC-Read Gas Property Invalid Conditions95
Configure AGA8 Parameters96
Configure Continuous Flow Analysis Parameters97
- Set Baseline Parameters97
Configure the Local Display98
Figure 5-13 Field Setup Wizard - Local Display98
Table 5-16 Local Display Labels, Descriptions and Valid Units99

Section 6: Archive Logs103

Section 7: Tools Commands139

Appendix A: Conversion Factors155

Appendix B: Miscellaneous Equations157

Appendix C: Troubleshooting Comm., Mech., and Elec161

Appendix D: Flow Rate Summary Charts165

Flow Rate Summary Charts165

Appendix E: Write-Protected Configuration Parameters169

Appendix F: Engineering Drawings183

3410 Series Engineering Drawings183

Appendix G: Index189

G.1 Manual Index189

Brand	Emerson
Model	Daniel 3410 Series
Category	Measuring Instruments
Language	English

Emerson Daniel 3410 Series User Manual

Table of Contents

Other manuals for Emerson Daniel 3410 Series

Questions and Answers:

Emerson Daniel 3410 Series Specifications

Related product manuals