Endress+Hauser iTEMP TMT82 - Output

iTEMP TMT82 Technical data
Endress+Hauser 45
Thermocouples as
per standard
Description Measuring range limits Min. span
IEC 60584, Part 1
Type A (W5Re-W20Re) (30)
Type B (PtRh30-PtRh6) (31)
Type E (NiCr-CuNi) (34)
Type J (Fe-CuNi) (35)
Type K (NiCr-Ni) (36)
Type N (NiCrSi-NiSi) (37)
Type R (PtRh13-Pt) (38)
Type S (PtRh10-Pt) (39)
Type T (Cu-CuNi) (40)
0 to +2 500 °C (+32 to +4 532 °F)
+40 to +1 820 °C (+104 to +3 308 °F)
–270 to +1 000 °C (–454 to +1 832 °F)
–210 to +1 200 °C (–346 to +2 192 °F)
–270 to +1 372 °C (–454 to +2 501 °F)
–270 to +1 300 °C (–454 to +2 372 °F)
–50 to +1 768 °C (–58 to +3 214 °F)
–50 to +1 768 °C (–58 to +3 214 °F)
–260 to +400 °C (–436 to +752 °F)
Recommended temperature range:
0 to +2 500 °C (+32 to +4 532 °F)
+500 to +1 820 °C (+932 to +3 308 °F)
–150 to +1 000 °C (–238 to +1 832 °F)
–150 to +1 200 °C (–238 to +2 192 °F)
–150 to +1 200 °C (–238 to +2 192 °F)
–150 to +1 300 °C (–238 to +2 372 °F)
+50 to +1 768 °C (+122 to +3 214 °F)
+50 to +1 768 °C (+122 to +3 214 °F)
–150 to +400 °C (–238 to +752 °F)
50 K (90 °F)
50 K (90 °F)
50 K (90 °F)
50 K (90 °F)
50 K (90 °F)
50 K (90 °F)
50 K (90 °F)
50 K (90 °F)
50 K (90 °F)
IEC 60584, Part 1;
ASTM E988-96
Type C (W5Re-W26Re) (32) 0 to +2 315 °C (+32 to +4 199 °F) 0 to +2 000 °C (+32 to +3 632 °F) 50 K (90 °F)
ASTM E988-96 Type D (W3Re-W25Re) (33) 0 to +2 315 °C (+32 to +4 199 °F) 0 to +2 000 °C (+32 to +3 632 °F) 50 K (90 °F)
DIN 43710
Type L (Fe-CuNi) (41)
Type U (Cu-CuNi) (42)
–200 to +900 °C (–328 to +1 652 °F)
–200 to +600 °C (–328 to +1 112 °F)
–150 to +900 °C (–238 to +1 652 °F)
–150 to +600 °C (–238 to +1 112 °F)
50 K (90 °F)
GOST
R8.8585-2001
Type L (NiCr-CuNi) (43) –200 to +800 °C (–328 to +1 472 °F) –200 to +800 °C (+328 to +1 472 °F) 50 K (90 °F)
• Internal cold junction (Pt100)
• External cold junction: configurable value –40 to +85 °C (–40 to +185 °F)
• Maximum sensor wire resistance 10 kΩ (If the sensor wire resistance is greater than 10 kΩ, an error message is output in
accordance with NAMUR NE89.)
Voltage
transmitter (mV)
Millivolt transmitter (mV) –20 to 100 mV 5 mV
Type of input The following connection combinations are possible when both sensor inputs are assigned:
Sensor input 1
Sensor input 2
RTD or
resistance
transmitter,
2-wire
RTD or
resistance
transmitter,
3-wire
RTD or
resistance
transmitter,
4-wire
Thermocouple
(TC), voltage
transmitter
RTD or resistance
transmitter, 2-wire
  - 
RTD or resistance
transmitter, 3-wire
  - 
RTD or resistance
transmitter, 4-wire
- - - -
Thermocouple (TC),
voltage transmitter
   
12.2 Output
Output signal
Analog output 4 to 20 mA, 20 to 4 mA (can be inverted)
Signal encoding FSK ±0.5 mA via current signal
Data transmission rate 1200 baud
Galvanic isolation U = 2 kV AC (input/output)
Failure information Failure information as per NAMUR NE43: