GALLONS /
BARREL
NOM. DIAM.
UNIT
FULL SCALE 2
PULSE WIDTH
RELAY 1
OFF-VALUE
RELAY 2
OFF-VALUE
ACTIVE RANGE
FULL SCALE
FREQ.
VOLUME
UNIT
DUAL RANGE
MODE
PULSE VALUE
RELAY 1
ON-VALUE
RELAY 2
ON-VALUE
CURRENT SPAN
FAILSAFE MODE
SIMULATION
CURR.
NOMINAL
CURRENT
OUTPUT SIGNAL
SIMULATION
FREQ.
NOMINAL FREQ.
FLOW RATE
UNIT
FULL SCALE 1
OPERATION
MODE
RELAY 1
FUNCTION
RELAY 2
FUNCTION
TIME CONSTANT
FULL SCALE
FLOW
FAILSAFE MODE
SYSTEM UNITS
CURRENT OUTPUT
PULSE / FREQ. OUTPUT
RELAYS
DISPLAY
PROCESSING PARA.
COMMUNICATION
BATCHING
SYSTEM PARAMETER
SENSOR DATA
CONTRAST LCD
LANGUAGE
ASSIGN LINE 2
TOTAL
OVERFLOW
DISPLAY DAMPING
RESET TOTALIZER
DISPLAY FORMAT
FLOW RATE
NOISE SUPPRESS.
MEASURING
MODE
FLOW DIRECTION
FUNCTION ECC
RECOVERY TIME
ECC
AMPLIFIER MODE
DELAY
BATCH VARIABLE
BATCH QUANTITY
BATCH PREWARN
COMPENS.
QUANTITY
BATCHING
MAX. BATCH TIME
BATCH CYCLE
RESET BATCH
CYC.
ASSIGN LINE 1
TOTAL VOLUME
LOW FLOW
CUTOFF
PROTOCOL
BUS ADDRESS
START
PULSE WIDTH
SYSTEM CONFIG.
ASSIGN
AUX. INPUT
EMPTY PIPE DET.
EPD RESPONSE
TIME
DEF.
PRIVATE CODE
ZERO POINT
NOMINAL
DIAMETER
MAX.
SAMPLING RATE
POS.
ZERO RETURN
K-FACTOR
NEGATIVE
PRESENT SYSTEM
CONDITION
ACCESS
CODE
SELF
CHECKING
K-FACTOR
POSITIVE
SAMPLING RATE
SERIAL NUMBER
EPD ELECTRODE
POLARITY
ECC
PREVIOUS SYSTEM
CONDITIONS
SOFTWARE
VERSION
SOFTWARE
VER. COM
p. 57
ba009d03
p. 47
p. 49
p. 53
p. 58
p. 66
p. 64
p. 69
p. 72
p. 77
p. 81 p. 81
p. 77
p. 72
p. 69
p. 66
p. 64
p. 59
p. 53
p. 50
p. 47
p. 81
p. 78
p. 73
p. 69
p. 67
p. 64
p. 59
p. 53
p. 51
p. 48
p. 81
p. 78
p. 74
p. 71
p. 67
p. 65
p. 62
p. 54
p. 51
p. 48
p. 82
p. 79
p. 75
p. 71
p. 67
p. 65
p. 62
p. 55
p. 51
p. 82
p. 79
p. 75
p. 67
p. 65
p. 62
p. 56
p. 51
p. 82
p. 80
p. 75
p. 68
p. 65
p. 57
p. 51
p. 82
p. 80
p. 76
p. 68
p. 65
p. 57
p. 52
p. 83
p. 76
p. 68
p. 57
p. 52
p. 68
p. 76
*)
These functions are only displayed if
other functions have been configured
accordingly.
Cross reference to detailed
function description
The Promag 33 electronis are fitted with various
electronics modules (HART or RS 485) depending
on the specifications when ordering. Depending
on the module, certain functions and function
groups are not available.
*) If a batching variable is activated, the “BATCHING”
function group is first shown on the display when entering
the operating matrix. The “BATCH QUANTITY” function
then moves into first position within this group.
Promag 33 5 Display and Operation
Endress+Hauser 37
To Next Page
Loading...
