Enertech VS Series - VT Series, Pressure Drop Tables

67
IOM, VS/VT Models, Rev A Enertech Global
VT Series, Pressure Drop Tables
PSI FT HD PSI FT HD PSI FT HD PSI FT HD
2.0 1.2 2.8 1.1 2.5 1.0 2.3 0.9 2.1
3.0 1.8 4.2 1.6 3.7 1.4 3.2 1.3 3.0
4.0 2.3 5.3 2.1 4.8 1.9 4.4 1.8 4.2
5.0 3.0 6.9 2.7 6.2 2.5 5.8 2.3 5.3
3.0 1.8 4.2 1.6 3.7 1.4 3.2 1.3 3.0
4.5 2.8 6.5 2.4 5.5 2.2 5.1 2.0 4.6
6.0 3.9 9.0 3.4 7.8 3.1 7.2 2.8 6.5
8.0 5.6 12.9 4.9 11.3 4.4 10.1 4.0 9.2
3.0 1.8 4.2 1.6 3.7 1.5 3.5 1.4 3.2
4.5 1.9 4.4 1.7 3.9 1.6 3.7 1.6 3.7
6.0 2.5 5.8 2.2 5.1 2.1 4.8 2.0 4.6
8.0 3.5 8.1 3.1 7.2 2.9 6.7 2.9 6.7
4.5 2.3 5.3 2.2 5.1 2.2 5.1 2.1 4.8
7.0 3.1 7.2 3.0 6.9 2.9 6.7 2.9 6.7
9.0 3.6 8.3 3.4 7.8 3.4 7.8 3.3
7.6
11.0 4.5 10.4 4.3 9.9 4.2 9.7 4.1 9.5
4.0 1.9 4.4 1.7 3.9 1.7 3.9 1.6 3.7
6.0 2.5 5.8 2.3 5.3 2.3 5.3 2.2 5.1
8.0 3.4 7.8 3.2 7.4 3.1 7.2 3.0 6.9
10.0 5.2 12.0 4.8 11.1 4.7 10.8 4.5 10.4
6.0 2.7 6.2 2.4 5.5 2.2 5.1 2.1 4.8
9.0 4.2 9.7 3.8 8.8 3.5 8.1 3.4 7.8
12.0 6.4 14.8 5.8 13.4 5.3 12.2 5.2 12.0
15.0 9.0 20.8 8.1 18.7 7.5 17.3 7.3 16.8
5.0 2.0 4.6 1.8 4.2 1.6 3.7 1.5 3.5
7.5 3.3 7.6 2.9 6.7 2.6 6.0 2.4 5.5
10.0 5.0 11.5 4.4 10.1 4.0 9.2 3.6 8.3
12.0 6.6 15.2 5.8 13.4 5.2 12.0 4.8 11.1
7.5 3.4 7.8 3.0 6.9 2.7 6.2 2.5 5.8
11.3 6.1 14.1 5.3 12.2 4.8 11.1
4.4 10.1
15.0 9.3 21.5 8.1 18.7 7.3 16.8 6.7 15.5
18.0 12.3 28.4 10.8 24.9 9.7 22.4 8.9 20.5
6.0 2.6 6.0 2.4 5.5 2.2 5.1 2.1 4.8
9.0 4.0 9.2 3.6 8.3 3.4 7.8 3.2 7.4
12.0 6.0 13.8 5.4 12.5 5.0 11.5 4.8 11.1
14.0 7.5 17.3 6.8 15.7 6.3 14.5 6.0 13.8
9.0 4.2 9.7 3.7 8.5 3.4 7.8 3.3 7.6
13.5 7.4 17.1 6.6 15.2 6.0 13.8 5.7 13.1
18.0 11.3 26.1 10.1 23.3 9.2 21.2 8.8 20.3
21.0 14.4 33.2 12.8 29.5 11.7 27.0 11.2 25.8
Source Brine Pressure Drop
VT036
Full Load
Model GPM
VT024
Part Load
VT024
Full Load
VT036
Part Load
1. Pressure drop data is based on 15% (by mass) methanol antifreeze solution (multiplier: 485).
30
o
F
50
o
F
70
o
F
90
o
F
VT060
Full Load
VT072
Part Load
VT072
Full Load
VT048
Part Load
VT048
Full Load
VT060
Part Load
6. Due to variations in installation, actual unit performance may vary from the tabulated data.
2. Pressure drop data accurate within ±25%.
3. Unit performance test is run without hot water generation.
4. Interpolation of unit pressure drop data is permissible; extrapolation is not.
5. Pressure drop data is a result of lab testing and is not related to warranty.
Section 11: Equipment Start-Up Procedures