Epson EB-S04 User Manual

19
Projector Placement
You can place the projector on almost any flat surface to project an image.
If you cannot install the projector parallel to the screen, correct
keystone distortion using the projector controls.
You can also install the projector in a ceiling mount if you want to use it in a
a
fixed location. An optional ceiling mount is required when suspending the
projector from a ceiling.
Warning
Note the following points when selecting a projector location:
• You must install a ceiling mount when suspending the projector from a ceiling.
• Place the projector on a sturdy, level surface or install it using a compatible
If you do not install the projector correctly, it could fall and cause damage or
mount.
injury.
• Do not use adhesives on the ceiling mount fixing points to prevent the screws
from loosening, or use lubricants, oils, or similar substances on the projector; the
projector case may crack causing it to fall from its ceiling mount. This could
cause serious injury to anyone under the ceiling mount and could damage the
projector.
• Do not cover the projector's air intake or air exhaust vents. If the vents are
covered, the internal temperature could rise and cause a fire.
Attention
• Do not operate the projector on its side. This may cause the projector to
malfunction.
• Leave plenty of space around and under the projector for ventilation, and
• If you are using the projector at altitudes above 1500 m, set the High Altitude
do not place it on top of or next to anything that could block the vents.
Mode setting to On in the projector's Extended menu to ensure the projector's
internal temperature is regulated properly.
• Position the projector within reach of a grounded electrical outlet or
s Extended > Operation > High Altitude Mode
extension cord.
• Place the projector parallel to the screen.
gg Related Links
• "Projector Setup and Installation Options" p.19
• "Projection Distance" p.20
• "Image Shape" p.41
• "Projector Setup Settings - Extended Menu" p.107
• "Optional Accessories" p.148
Projector Setup and Installation Options
You can set up or install your projector in the following ways:

Epson EB-S04 Specifications

General

Native aspect ratio	-
Projection distance	1.77 - 2.4 m
Projection technology	3LCD
Contrast ratio (typical)	15000:1
Projection distance (wide)	0.88 - 10.44 m
Projector native resolution	SVGA (800x600)
Keystone correction, vertical	-30 - 30 °
Keystone correction, horizontal	- 30 - 30 °
Projector brightness (economic mode)	2100 ANSI lumens
Focus	Manual
Throw ratio	1.45 - 1.96:1
Digital zoom	1.35 x
Lamp type	UHE
Lamp power	200 W
Light source type	Lamp
Service life of light source	5000 h
Service life of light source (economic mode)	10000 h
RMS rated power	1 W
Number of built-in speakers	1
Placement	Desktop, Ceiling
Product type	Standard throw projector
Product color	White
Built-in display	No
Power source	AC
AC input voltage	100 - 240 V
AC input frequency	50 - 60 Hz
Power consumption (standby)	0.26 W
Power consumption (typical)	277 W
Power consumption (economy mode)	207 W
Ethernet LAN (RJ-45) ports	0
Cables included	AC, VGA
Remote control type	IR
Operating altitude	0 - 3000 m
Operating temperature (T-T)	5 - 35 °C
Operating relative humidity (H-H)	20 - 80 %
Noise level	37 dB
Country of origin	Philippines
Noise level (economic mode)	28 dB
USB connector type	USB Type-A, USB Type-B
HDMI connector type	Full-size
USB 2.0 ports quantity	2
Pallet width	800 mm
Pallet height	1190 mm
Pallet length	1200 mm
Pallet width (UK)	1000 mm
Quantity per pack	1 pc(s)
Quantity per pallet	78 pc(s)
Quantity per pallet layer	6 pc(s)

Weight and Dimensions

Depth	234 mm
Width	297 mm
Height	77 mm
Weight	2400 g
Package depth	360 mm
Package width	350 mm
Package height	160 mm
Package weight	3829 g