How to calibrate the screen on EXFO FTB-2 Measuring Instruments?
If the screen calibration on your EXFO Measuring Instruments unit is not maintained or is difficult to calibrate properly, reset the calibration settings. From the Control Panel, go to Hardware and Sound > Tablet PC Settings. Tap Reset. If further adjustments are needed, use ToolBox X: tap System Settings > Touch Screen Calibration.
What to do if EXFO Measuring Instruments unit does not recognize a test module?
If your EXFO Measuring Instruments unit doesn't recognize a test module: * Install the corresponding application using the Update Manager application. * If the unit recognizes other modules, the one you are trying to use could be defective. * Ensure that the module is supported on your unit by referring to the unit’s technical specifications.
Why can't I access the internet with my EXFO FTB-2 Measuring Instruments using a mobile broadband USB modem key?
If you cannot access the Internet with your EXFO Measuring Instruments unit using a mobile broadband USB modem key, consider these possible causes: * Ensure that the SIM card is properly inserted into the USB modem key. * Try disconnecting and reconnecting the modem key, or try a different USB port. * Contact your mobile service provider to verify that the SIM card is activated and that there are no issues with your service or the mobile network.
Why is my EXFO FTB-2 unit running slower than expected?
If your EXFO Measuring Instruments unit is running slower than expected, it may be due to Windows components configuring in the background. Leave the unit idle for about an hour to allow Windows to complete these tasks.
Why are the batteries in my EXFO Measuring Instruments not recharging?
If the batteries in your EXFO Measuring Instruments are not recharging, check the following: * Ensure the ambient temperature is within the specified range for recharging. * For FTB-2 and FTB-2 Pro units: verify the AC adapter is connected to the unit and the AC power cord is connected to both the adapter and the AC outlet. For FTB-4 units: ensure the power cord is properly connected to the unit and the AC outlet.
What to do if EXFO FTB-2 unit is not responding?
If your EXFO Measuring Instruments unit is not responding, force a hardware reset by pressing the On/Off button for at least fifteen seconds.
What to do if the USB device I connected to EXFO Measuring Instruments is not working?
If a USB device isn't working after you connect it to your EXFO Measuring Instruments unit: * Try disconnecting and reconnecting the device. * Turn the unit off and then on again. * Make sure you have the correct driver for the device, which may be provided with the device or available online.
Overview of the platform's core hardware components and capabilities.
Critical safety guidelines and warnings related to laser operation and potential hazards.
Essential safety instructions and warnings concerning electrical hazards and proper usage.
Instructions on how to properly ground the unit for safety and protection against overvoltages.
Guides users through the initial Windows and EXFO wizard setup process.
How to configure instruments for remote access, standalone use, and identification.
A guide to common issues and their solutions, including unit startup and response problems.
Procedures for restoring the unit to a previous state or factory settings using WIM files.
Information on how to contact EXFO technical support for assistance.
A summary of required commands compliant with the IEEE 488.2 standard.
A summary of commands specific to the unit, with explanations on following pages.
An overview of ActiveX and COM components for building applications.
How to send SCPI commands remotely using Telnet from Windows or Linux clients.
General| Category | Measuring Instruments |
|---|---|
| Model | FTB-2 |
| Manufacturer | EXFO |
| Platform Type | Modular |
| Modular Slots | 2 |
| Type | Optical Test Platform |
| Applications | Optical network testing |
| Modules Supported | Various EXFO modules |
| Display | Touchscreen |
| Operating Temperature | -10°C to 50°C |
| Storage Temperature | -40°C to 70°C |
| Interfaces | USB, Ethernet |
| Connectivity | Wi-Fi |
| Power | AC/DC adapter, rechargeable battery |
To Next Page
