To Next PageTo Next PageWhat to do if Fronius TransTig 2200 Welding System tS3 error occurs?
If the Fronius Welding System displays a tS3 error, it indicates overtemperature in the power source's secondary circuit. Allow the power source to cool down.
What to do if Fronius TransTig 2200 tSt error occurs?
If the Fronius Welding System displays a tSt error, it indicates overtemperature in the power source control circuit. Allow the power source to cool down.
General| Welding Process | TIG, MMA |
|---|---|
| Input Voltage | 230 V |
| Input Current | 16 A |
| Output Current Range (MMA) | 10 - 220 A |
| Duty Cycle (TIG) | 60 % at 220 A |
| Protection Class | IP23 |
| Insulation Class | F |
| Power Supply Voltage | 230 V |
| Cooling | Air-cooled |
Explains the meaning of danger, warning, and caution symbols used in the manual.
Covers general device safety, operator obligations, and intended use guidelines.
Details operator responsibilities, required training, and personnel duties.
Covers risks from sparks, radiation, fields, current, noise, and fumes.
Details dangers of electric shock from mains and welding current.
Addresses EMF risks, moving parts hazards, and hot components.
Specifies shielding gas quality and covers safety for gas cylinders.
Warns about escaping gas and details safety for installation and transport.
Emphasizes ensuring safety devices are functional during device operation.
Guidelines for commissioning, maintenance, repair, and periodic safety inspections.
Details the controls and indicators on the MagicWave control panel.
Details the controls and indicators on the TransTig control panel.
Warns about incorrect operations and electric shock risks during installation.
Defines intended use, device regulations (IP 23), and mains connection.
Provides safety warnings for start-up and notes on using cooling units.
Introduces commissioning and details safe gas cylinder connection.
Guides on grounding the workpiece and connecting the welding torch.
Warns about incorrect operation and electric shock risks when using TIG modes.
Describes the 2-step welding process and its spot welding functionality.
Warns about incorrect operation and electric shock risks during TIG welding.
Explains how to navigate and display welding parameters on the device.
Details essential TIG parameters like Starting current, UpSlope, and Main current.
Outlines the steps required to prepare for TIG welding.
Describes the HF ignition procedure, its benefits, and safety precautions.
Explains the touchdown ignition procedure and conditions for its use.
Explains the TIG pulsing function for improved weld pool control.
Describes the TIG cold-wire welding process with a cold wire feeder.
Warns about incorrect operation and electric shock risks during MMA welding.
Explains parameter display and navigation for MMA welding.
Details MMA parameters like Starting current and Main current.
Outlines preparation steps and MMA mode selection.
Warns about incorrect operation and electric shock risks when managing jobs.
Explains parameter display and navigation for welding jobs.
Details TIG welding parameters within job management.
Details rod electrode parameters within job management.
Guides on preparing and saving settings as a job.
Provides steps to access and navigate the TIG setup menu.
Guides on selecting and modifying TIG setup parameters.
Details parameters like Spot welding time and Tacking function.
Provides steps to access and navigate the TIG setup 2nd menu.
Provides a step-by-step guide for calibrating the push-pull unit.
Lists service codes, causes, and remedies for open-circuit calibration.
Lists service codes, causes, and remedies for engaged calibration.
Step-by-step guide to optimizing a selected welding job.
Step-by-step guide to delete a selected welding job.
Provides steps to perform a factory reset of the welding machine.
Covers general principles, safety, and handling service codes.
Troubleshooting for power source functionality and current/voltage issues.
Warns about incorrect work and electric shock risks during maintenance.
Warns about inadequately dimensioned electrical installations.
