GE B90 - Page 502

iv B90 LOW IMPEDANCE BUS DIFFERENTIAL SYSTEM – INSTRUCTION MANUAL
INDEX
EnerVista UR setup
command line interface ..................................................................C-1
drag and drop files .............................................................................4-3
event recorder ......................................................................................4-2
firmware upgrade or downgrade ..........................................10-13
installation ........................................................................................... 3-50
oscillography .........................................................................................4-2
requirements ..................................................................................... 3-49
restart relay ...........................................................................................5-1
Engineer
command to force user logoff ......................................................7-4
create logic diagram ...................................................................... 4-61
Error messages ................................................................................. 4-69
Warning messages ......................................................................... 4-70
Engineer toolbar .................................................................................. 4-80
Enhanced front panel
FlexLogic ............................................................................................5-142
interface ............................................................................................... 4-14
keypad .................................................................................................. 4-37
labels ...................................................................................................... 4-43
LEDs ..........................................................................................4-39, 5-110
navigation ........................................................................................... 4-50
order codes ............................................................................................2-7
pushbuttons .....................................................................................5-113
specifications ..................................................................................... 2-18
use, change setting ......................................................................... 4-52
Environment backup ........................................................................ 10-9
Equations
definite time curve ........................................................................5-174
FlexLogic ............................................................................................5-153
FlexLogic, protect ................................................................................4-9
IAC curves ..........................................................................................5-172
IEC curves ..........................................................................................5-171
IEEE curves ........................................................................................5-170
Equipment mismatch error ..............................................................7-5
Error messages .......................................................................................7-5
device not recognized .................................................................10-13
in Engineer .......................................................................................... 4-69
Ethernet
actual values .........................................................................................6-6
configuration ..................................................................................... 3-57
port settings ....................................................................................... 5-41
port, turn on or off ........................................................................... 5-41
ports on rear panel ............................................................................3-6
Quick Connect ................................................................................... 3-62
Event cause indicators .................................................................... 4-39
Event Cause LEDs ............................................................................... 4-41
Event recorder
actual values ...................................................................................... 6-12
clearing ........................................................................................5-36, 7-2
records explained ...............................................................................4-2
specifications ..................................................................................... 2-19
system logs ......................................................................................... 5-22
via EnerVista software ......................................................................4-2
EVENTS setting ........................................................................................5-4
Export settings to file ........................................................................ 10-8
F
F485 ............................................................................................................3-49
Factory default reset ................................................................5-5, 5-19
Far-End Fault Indication ..................................................................5-42
Fast form-C relay specifications .................................................2-22
Fast transient testing specifications ........................................2-27
Features .......................................................................................................2-1
Fiber signal loss detection .............................................................5-42
File transfer by IEC 61850 ..............................................................5-91
File transfer by TFTP ..........................................................................5-92
Files
delete .................................................................................................. 10-29
download .............................................................................................10-3
drag and drop .......................................................................................4-3
protect FlexLogic with password .................................................4-9
protect with password ......................................................................4-7
transfer from relay ..........................................................................4-15
transfer to relay .......................................................................4-1, 4-15
Firmware lock self-test ....................................................................7-10
Firmware not supported by EnerVista ................................. 10-14
Firmware revision ...............................................................................6-14
Firmware upgrade or downgrade .......................................... 10-13
Firmware version does not match EnerVista ................... 10-13
Flash memory .................................................................................... 10-29
Flash messages ....................................................................................5-23
Flex State parameters
actual values .........................................................................................6-6
settings ............................................................................................... 5-119
specifications .....................................................................................2-18
FlexAnalog parameters ......................................................................A-1
FlexCurves
settings ............................................................................................... 5-130
specifications .....................................................................................2-17
table ..................................................................................................... 5-130
FlexLogic
create logic diagram with Engineer ........................................4-61
edit with equation editor ........................................................... 5-153
equation editor ............................................................................... 5-153
error messages ....................................................................................7-6
evaluation ......................................................................................... 5-147
example ............................................................................................. 5-148
gate characteristics ..................................................................... 5-146
lock equations ......................................................................................4-9
lock equations to serial number ...............................................4-11
operands ........................................................................................... 5-141
operators ........................................................................................... 5-146
rules ..................................................................................................... 5-147
security .....................................................................................................4-9
specifications .....................................................................................2-17
timer settings .................................................................................. 5-153
worksheet ......................................................................................... 5-150
Force contact inputs ...................................................................... 5-202
Force contact outputs ................................................................... 5-203