GE B90 - Page 507

INDEX
B90 LOW IMPEDANCE BUS DIFFERENTIAL SYSTEM – INSTRUCTION MANUAL ix
R
RADIUS server
authentication ....................................................................................5-13
setup .........................................................................................................B-1
RAM required ..........................................................................................3-49
Real-time clock
actual values for synchronization .............................................. 6-6
settings ..................................................................................................5-99
Reboot relay
using EnerVista ....................................................................................5-1
using relay .............................................................................................. 7-3
Recloser curves ..................................................................................5-133
Redundancy
PRP actual values ............................................................................... 6-8
PRP explained .....................................................................................5-43
settings ..................................................................................................5-41
specifications ......................................................................................2-24
Relay architecture ............................................................................5-139
Relay maintenance ............................................................................... 7-3
Relay name ..........................................................................................5-128
Release Notes .....................................................................................10-14
Remote access of front panel in EnerVista ................. 4-16, 6-2
Remote access, explained ................................................................ 5-6
Remote Setting Authorization ...................................................10-14
Repair ...................................................................................1-2, 10-29, D-1
Replace battery .................................................................................10-24
Replace battery message .................................................................7-7
Replace front panel .........................................................................10-15
Replacement modules ......................................................................2-12
Requirements for installation .......................................................3-49
Reset to factory defaults ....................................................... 5-5, 5-19
Resetting
FlexLogic operands .......................................................................5-145
setting to clear LEDs and messages ....................................5-196
to factory defaults .............................................................................. 5-5
Restart relay
using EnerVista ....................................................................................5-1
using relay .............................................................................................. 7-3
Restore settings ....................................................................................10-8
Revision history .......................................................................................D-1
RF immunity specifications ............................................................2-27
RFI, conducted specifications .......................................................2-27
R-GOOSE description .........................................................................5-62
RJ-45 ....................................................................................................2-7, 3-6
RMS current specifications ............................................................2-19
Roles for login ..........................................................................................2-5
Routable GOOSE ...................................................................................5-62
RS232
baud rate ..............................................................................................5-38
configuration ......................................................................................3-61
specifications ......................................................................................2-23
wiring ......................................................................................................3-26
RS422
configuration ...................................................................................... 3-38
timing .....................................................................................................3-39
two-channel application ..............................................................3-38
with fiber interface ..........................................................................3-40
RS485
description ........................................................................................... 3-28
port on rear panel ...............................................................................3-6
settings .................................................................................................5-38
specifications .....................................................................................2-23
Rules for passwords .............................................................................5-5
RxGOOSE
actual values ......................................................................................6-11
error messages ....................................................................................7-9
FlexAnalogs ............................................................................................A-3
settings .................................................................................................5-67
S
Save settings ............................................................................................4-1
Saving setting does not take relay out of service ...............5-1
SCADA protocol selection ...............................................................5-47
SCD file
import ..................................................................................................10-12
import preferences ..........................................................................10-9
SCL compatible ....................................................................................5-53
SCL file import ...............................................................5-71, 5-73, 5-74
preferences .........................................................................................10-9
Security
commands .............................................................................................7-4
delete files and records ...............................................................10-29
EnerVista and UR secure with SSH .............................................2-4
failed authentication lockout .....................................................5-19
forceful user logout ............................................................................7-3
lock FlexLogic equations .................................................................4-9
password for settings template ...................................................4-7
passwords for settings and commands .............4-59, 5-7, 5-8
RADIUS server for user authentication .....................................B-1
role-based user access ....................................................................2-5
settings .................................................................................................5-17
software options ..............................................................................2-25
specifications .....................................................................................2-25
system and event logs ...................................................................5-22
Security audit list of port numbers ........................................... 5-41
Self-tests
description ..............................................................................................7-5
error messages ....................................................................................7-5
FlexLogic operands .......................................................................5-145
user-programmable .....................................................................5-111
Serial number ...................................................................3-1, 4-11, 6-14
Serial ports
settings .................................................................................................5-38
specifications .....................................................................................2-23
Server authentication .......................................................................5-13
Server unavailable self-test ..........................................................7-10
Service life expected .........................................................................10-3
Service Report ..........................................................................................1-2