GE B90 - Page 506

viii B90 LOW IMPEDANCE BUS DIFFERENTIAL SYSTEM – INSTRUCTION MANUAL
INDEX
Parallel Redundancy Protocol
actual values .........................................................................................6-8
explained ............................................................................................. 5-43
settings ................................................................................................. 5-41
specifications ..................................................................................... 2-24
Parity .......................................................................................................... 5-38
Part numbering .......................................................................................2-7
Passwords
authentication by device or server .......................................... 5-13
bypass authentication ................................................................... 5-20
change .................................................................................................. 4-58
change after installation .............................................................. 3-63
change does not take relay out of service .............................5-1
command ..........................................................................4-59, 5-7, 5-8
default ................................................................................................... 5-11
explained ................................................................................................2-4
FlexLogic operands .......................................................................5-145
lockout ...................................................................................... 4-60, 5-11
lost password .......................................................................................5-5
requirements ........................................................................................5-5
reset to factory defaults ..................................................................5-5
rules ...........................................................................................................5-5
settings ...............................................................................4-59, 5-7, 5-8
settings templates ..............................................................................4-7
wrong entry ........................................................................................ 4-60
Per-unit quantity ....................................................................................5-3
Phase angle metering .........................................................................6-9
Phasor display graphical front panel .......................... 4-57, 5-28
Plastic film on front panel ............................................................10-20
Port
Ethernet, turn on or off .................................................................. 5-41
HTTP, close .......................................................................................... 5-91
IEC 60870-5-104, close ................................................................. 5-93
Modbus, close .................................................................................... 5-47
on rear panel ........................................................................................3-6
SNTP, close ........................................................................................5-103
TFTP, close ........................................................................................... 5-92
USB ......................................................................................................... 4-15
Port number
combinations with protocols ...................................................... 5-47
connectivity report of those used ............................................ 4-76
DNP ......................................................................................................... 5-48
HTTP ....................................................................................................... 5-91
IEC 60870-5-104 .............................................................................. 5-92
list of ....................................................................................................... 5-41
Modbus ................................................................................................. 5-46
Modbus during installation ......................................................... 3-58
RADIUS .................................................................................................. 5-16
SNTP .....................................................................................................5-103
system log ............................................................................... 5-16, 5-17
TFTP ........................................................................................................ 5-92
Power supply
description .......................................................................................... 3-13
diagram ...................................................................................................3-6
removal to replace battery .......................................................10-24
specifications ..................................................................................... 2-21
Power System
settings ...............................................................................................5-129
Precision Time Protocol
actual values for port state ............................................................6-6
clock settings .....................................................................................5-99
error message ......................................................................................7-7
port behavior ......................................................................................5-42
settings ............................................................................................... 5-100
specifications .....................................................................................2-24
Preferences
comparing settings .........................................................................10-7
Engineer ................................................................................................4-76
IEC 61850 .............................................................................................5-57
import file .............................................................................................10-9
Preserve custom attributes when importing SCD/CID files ..
10-9
Print front panel labels .........................................................4-43, 4-75
Product information
actual values ......................................................................................6-14
Device Connectivity Report in Engineer ................................4-76
firmware revision .............................................................................6-14
Product setup ...........................................................................................5-5
Programmed mode ............................................................................3-47
Protection elements .............................................................................5-3
Protection Summary interface ............................3-61, 4-4, 5-179
Protocol selection ...............................................................................5-47
Prototype firmware error message ..........................................7-11
PRP
actual values .........................................................................................6-8
explained ..............................................................................................5-43
settings ..................................................................................................5-41
specifications .....................................................................................2-24
PTP
actual values for port state ............................................................6-6
clock settings .....................................................................................5-99
error message ......................................................................................7-7
port behavior ......................................................................................5-42
settings ............................................................................................... 5-100
specifications .....................................................................................2-24
pu quantity .................................................................................................5-3
Pushbuttons
control FlexLogic ........................................................................... 5-142
control logic diagram .................................................................. 5-113
control settings .............................................................................. 5-112
control specifications .....................................................................2-18
testing .......................................................................................................7-3
user-programmable FlexLogic ............................................... 5-146
user-programmable logic diagrams .................................... 5-118
user-programmable settings .................................................. 5-113
user-programmable specifications .........................................2-18
Q
Quick Connect ...........................................................................3-61, 3-62