Hameg HM8118 Manual

30
Subject to change without notice
General remarks regarding the CE marking
General remarks regarding the CE marking
General remarks regarding the CE marking
HAMEG measuring instruments comply with the EMI norms. Our tests
for conformity are based upon the relevant norms. Whenever different
maximum limits are optional HAMEG will select the most stringent
ones. As regards emissions class 1B limits for small business will be
applied. As regards susceptability the limits for industrial environments
will be applied.
All connecting cables will inuence emissions as well as susceptability
considerably. The cables used will differ substantially depending on the
application. During practical operation the following guidelines should
be absolutely observed in order to minimize EMI:
1. Data connections
Measuring instruments may only be connected to external associated
equipment (printers, computers etc.) by using well shielded cables.
Unless shorter lengths are prescribed a maximum length of 3 m must
not be exceeded for all data interconnections (input, output, signals,
control). In case an instrument interface would allow connecting several
cables only one may be connected.
In general, data connections should be made using double-shielded
cables. For IEEE-bus purposes the double screened cable HZ72 from
HAMEG is suitable.
2. Signal connections
In general, all connections between a measuring instrument and the
device under test should be made as short as possible. Unless a shorter
length is prescribed a maximum length of 3 m must not be exceeded,
also, such connections must not leave the premises.
All signal connections must be shielded (e.g. coax such as RG58/U).
With signal generators double-shielded cables are mandatory. It is
especially important to establish good ground connections.
3. External inuences
In the vicinity of strong magnetic or/and electric elds even a careful
measuring set-up may not be sufcient to guard against the intrusion
of undesired signals. This will not cause destruction or malfunction of
HAMEG instruments, however, small deviations from the guranteed
specications may occur under such conditions.
HAMEG Instruments GmbH
KONFORMITÄTSERKLÄRUNG
DECLARATION OF CONFORMITY
DECLARATION DE CONFORMITE
DECLARACIóN DE CONFORMIDAD
Hersteller / Manufacturer / Fabricant / Fabricante:
HAMEG Instruments GmbH · Industriestraße 6 · D-63533 Mainhausen
Die HAMEG Instruments GmbH bescheinigt die Konformität für das Produkt
The HAMEG Instruments GmbH herewith declares conformity of the product
HAMEG Instruments GmbH déclare la conformite du produit
HAMEG Instruments GmbH certica la conformidad para el producto
Bezeichnung: LCR-Messbrücke
Product name: LCR-Bridge
Designation: Pont de Mesure RLC
Descripción: Puente de medida
Typ / Type / Type / Tipo: HM8118
mit / with / avec / con: HO820
Optionen / Options / HO880
Options / Opciónes: HZ184, HZ186, HZ188, HO118
mit den folgenden Bestimmungen / with applicable regulations /
avec les directives suivantes / con las siguientes directivas:
EMV Richtlinien / EMC Directives / Directives CEM / Directivas IEM:
2004/108/EG;
Niederspannungsrichtlinie / Low-Voltage Equipment Directive / Directive des
equipements basse tension / Directiva de equipos de baja tensión:
2006/95/EG
Angewendete harmonisierte Normen / Harmonized standards applied /
Normes harmonisées utilisées / Normas armonizadas utilizadas:
EMV allgemein / EMC general / CEM général / IEM general:
DIN EN 61326-1; VDE 0843-20-1: 10/2006
Sicherheit / Safety / Sécurité / Seguridad:
DIN EN 61010-1; VDE 0411-1: 08/2002
Überspannungskategorie / Overvoltage category / Catégorie de surtension /
Categoría de sobretensión: II
Verschmutzungsgrad / Degree of pollution / Degré de pollution /
Nivel de polución: 2
Elektromagnetische Verträglichkeit / Electromagnetic compatibility /
Compatibilité électromagnétique / Compatibilidad electromagnética:
EMV Störaussendung / EMI Radiation / Emission CEM / emisión IEM:
DIN EN 61000-6-3: 09/2007 (IEC/CISPR22, Klasse / Class / Classe / classe B)
VDE 0839-6-3: 04/2007
Störfestigkeit / Immunity / Imunitee / inmunidad:
DIN EN 61000-6-2; VDE 0839-6-2: 03/2006
Oberschwingungsströme / Harmonic current emissions / Émissions de courant
harmonique / emisión de corrientes armónicas:
DIN EN 61000-3-2; VDE 0838-2: 06/2009
Spannungsschwankungen u. Flicker / Voltage uctuations and icker /
Fluctuations de tension et du icker / uctuaciones de tensión y icker:
DIN EN 61000-3-3; VDE 0838-3: 06/2009
Datum / Date / Date / Fecha
12. 04. 2012
Unterschrift / Signature / Signatur / Signatura
Holger Asmussen
General Manager

Hameg HM8118 Specifications

General

Brand	Hameg
Model	HM8118
Category	Measuring Instruments
Language	English