Hameg HM8118 Manual

31
Subject to change without notice
Content
5.2.5 Frequency FRQ 45
5.2.6 Function FUNC 45
5.2.7 Reference value LOADM for the main
measurement value 45
5.2.8 Reference value LOADS for the second
measurement value 45
5.3 Menu function SYST 46
5.3.1 CONTRAST 46
5.3.2 KEY BEEP 46
5.3.3 TALK ONLY 46
5.3.4 Baud rate BAUDS 46
5.3.5 MAINS FRQ 46
5.3.6 Instrument information INFO 46
5.4 Storing / Recalling of instrument settings
and parameters 46
5.5 Factory settings 46
6 Calibration 47
6.1 Open circuit calibration procedure 47
6.2 Short circuit calibration procedure 47
6.3 Procedure of the calibration with a known load 47
7 Connecting of components and 48
7.1 4 wire measuring adapter HZ181 48
7.1.1 Specications 48
7.1.2 Calibration 48
7.2 Kelvin measurement cable HZ184 49
7.2.1 Specications 49
7.2.2 Calibration 49
7.3 4 wire transformer measurement cable HZ186 49
7.3.1 Specications 50
7.3.2 Calibration 50
7.4 4 wire SMD test adapter HZ188 50
7.4.1 Specications 50
7.4.2 Calibration 50
7.5 Option HO118 binning interface for
component sorting 51
7.5.1 Specication 51
7.5.2 Container (BIN) setup 52
7.5.3 Examples 52
8 Remote Control 53
8.1 Dual Interface HO820 (USB/RS-232) 53
8.2 IEEE-488 (GPIB) interface HO880 53
8.3 Communication 53
9 Command reference 54
9.1 Setup Commands 54
9.2 Control Commands 55
9.3 Commands for the request of results 55
9.4 Binning Commands 55
9.5 Setup and Control Commands 56
Content
Deutsch 3
English
General remarks regarding the CE marking 30
Programmable LCR-Bridge HM8118 32
Specications 33
1 Important hints 34
1.1 Symbols 34
1.2 Unpacking 34
1.3 Positioning 34
1.4 Transport and storage 34
1.5 Safety instructions 34
1.6 Proper operating conditions 34
1.7 Warranty and Repair 35
1.8 Maintenance 35
1.9 Line fuse 35
1.10 Power switch 35
2 Controls and display 36
3 Quick Introduction 38
3.1 Hardware supplied 38
3.2 Measurement of a capacitor 38
3.3 Measurement of an inductor 38
3.4 Measurement of a resistor 39
4 First-time operation 39
4.1 Connecting the instrument 39
4.2 Turning on the instrument 40
4.3 Line frequency 40
4.4 Measuring principle 40
4.5 Main measurement and second measurement value
display 40
4.6 Display of measurement results 41
4.7 Choosing of the measurement range 41
4.7.1 Automatic range selection 41
4.7.2 Manual range selection 41
4.8 Switching the equivalent measurement 42
circuitry 42
5 Setting of instrument parameters 43
5.1 Menu function SETUP 43
5.1.1 Frequency FRQ 43
5.1.2 Voltage LEV 43
5.1.4 Measuring range RNG 44
5.1.5 Measuring speed SPD 44
5.1.6 Triggering TRIG 44
5.1.7 DELAY 44
5.1.8 Average (AVG) 44
5.1.9 Display of test signal levels
V
m
(voltage) / I
m
(current) 44
5.1.10 Guarding GUARD 44
5.1.11 Deviation DEV_M 44
5.1.12 Reference REF_M 44
5.1.13 Deviation DEV_S 44
5.1.14 Reference REF_S 44
5.1.15 Constant voltage CST V 45
5.2 Menu function CORR 45
5.2.1 Calibration OPEN 45
5.2.2 Calibration SHORT 45
5.2.3 Calibration LOAD 45
5.2.4 NUM 45

Hameg HM8118 Specifications

General

Brand	Hameg
Model	HM8118
Category	Measuring Instruments
Language	English