Heal Force Smart-Mini

Questions and Answers

N
nhowardAug 11, 2025
How to troubleshoot no display on Heal Force Smart-Mini Water Filtration Systems?
- B
  Brian GarciaAug 11, 2025
  If your Heal Force Water Filtration System shows no display, several issues could be the cause. First, ensure the power outlet is working by testing it. If the outlet is loose, try a different one. Check that the system power cord is correctly plugged into both the outlet and the main unit. Make sure the power switch on the back of the unit is turned on. Inspect the power cord for any damage and replace it if necessary. Also, the fuse might be burned, so replace it. If none of these steps work, it could indicate an internal component failure, and you should contact technical service.
W
wmillsAug 25, 2025
Why is the pure water conductivity too high in Heal Force Water Filtration Systems?
- J
  jessica59Aug 25, 2025
  If the pure water conductivity is too high in your Heal Force Water Filtration System, it could be due to several reasons. If the feed water conductivity is high, consider choosing the RO-2 module. If the RO membrane is exhausted, showing an RO or DS alarm, replace it. If you've just installed a new reverse osmosis membrane, there might be remaining protection liquid; press the “ Flush/ ? ” button to rinse the membrane. If none of these steps work, there may be an internal component failure, and you should contact technical service.
M
mitchellrandallAug 29, 2025
What to do if the flow rate of ultra-pure water is too low in Heal Force Smart-Mini Water Filtration Systems?
- M
  miranda31Aug 29, 2025
  If the flow rate of ultra-pure water is too low in your Heal Force Water Filtration System, several factors could be the cause. If the system is in recycling mode, wait for the water production to reach the preset quality. If the ultra-pure water resistivity is too low or the set value is too high, adjust the ultra-pure water quality to the required level. Check that the RO OUT of the water tank is connected to the RO IN of the main unit. If none of these steps resolve the issue, there may be an internal component failure; in that case, contact technical service.
M
Mary CarterSep 4, 2025
Why is ultra-pure water resistivity too low in Heal Force Water Filtration Systems?
- K
  Kevin LongSep 5, 2025
  If the ultra-pure water resistivity is too low in your Heal Force Water Filtration System, it could be due to a few reasons. The purification cartridge might be exhausted, so replace it. The unit might be displaying conductivity value instead of resistivity; switch the unit mode to resistivity. Ensure the purification cartridge is correctly installed. If none of these steps work, it may indicate an internal component failure, and you should contact technical service.
T
tsmithNov 16, 2025
What to do if Heal Force Smart-Mini Water Filtration Systems are making RO water too slowly?
- T
  Thomas RossNov 16, 2025
  If your Heal Force Water Filtration System is producing RO water at a low rate, several factors could be responsible. Check that the external water supply is open. If the pre-filter is blocked, rinse it or replace it if needed. If the feed water pressure is too low, you might need an additional pressure pump. Ensure the feed water pipe is correctly connected to the FEED connector on the main unit. If the pretreatment is blocked, replace the pretreatment module. If there are impurities on the RO surface, press the “Flush/?” button to flush the RO. If the RO is blocked, replace the RO module. Verify that the RO OUT of the main unit is connected to the RO IN of the water tank. If the water temperature is too low, consider adding a preheat system. If none of these steps resolve the issue, ther...

Heal Force Smart-Mini Specifications

General

Brand	Heal Force
Model	Smart-Mini
Category	Water Filtration Systems
Language	English

Heal Force Smart-Mini - User Manual

Table of Contents

Questions and Answers

Heal Force Smart-Mini Specifications