Honeywell Gamewell-FCI GWF-7075 - 2: Current Draw Worksheet for Velociti SLC Devices

16 GWF-7075 Addressable Fire Alarm Control Panel Manual — P/N LS10147-002GF-E:E 06/11/2019
Installation Instructions Criteria Calculating Current Draw and Standby Battery
3.6.2 Current Draw Worksheet for Velociti SLC Devices
Use Table 3.3 to determine current requirements during alarm/battery standby operation when Velociti SLC devices are installed. You
can install up to 75 Velociti detectors and 75 Velociti modules
1
.
Device
Number of
Devices
Current per Device
Standby
Current
Alarm
Current
For each device use this formula: This column X This column = Current per number of devices.
Fire Panel (Current draw frombattery) 1 Standby: 165 mA 165 mA
Alarm: 310 mA 310 mA
Addressable SLC Detectors
ASD-PL2F Photo detector Standby/Alarm: .30 mA
6
mA mA
ASD-PTL2F Photo smoke w/thermal mA mA
ATD-L2F Fixed temperature thermal detector mA mA
ATD-HL2F Fixed high temperature thermal
detector
mA mA
MCS-Acclimate2F multi-criteria photoelectric
detector w/thermal
mA mA
ATD-RL2F Fixed heat detector mA mA
mA mA
ASD-PL3 / IV Photoelectric detector
(See Note 6)
SLC Standby: 200µAmA
Alarm: 4.5mA mA
ASD-PL3R / IV Photo RAT (See Note 6) SLC Standby: 200µAmA
Alarm: 4.5mA mA
ASD-PTL3 / IV Photo /Thermal (See Note 6) SLC Standby: 200µAmA
Alarm: 4.5mA mA
ATD-L3 / IV Heat detector SLC Standby: 200µA mA
Alarm: 4.5mA mA
ATD-L3R / IV heat detector -ROR SLC Standby: 200µAmA
Alarm: 4.5mA mA
ATD-L3H / IV Heat detector - high SLC Standby: 200µAmA
Alarm: 4.5mA mA
ABD-2F Beam detector (without integral test) SLC Standby/Alarm: 2 mA mA mA
Aux. Pwr Standby: 2 mA mA
Alarm: 8.5 mA mA
ABD-RT2F
4
Beam detector (with integral test) SLC Standby/Alarm: 2 mA
Aux. Pwr Standby: 2 mA mA
Alarm: 8.5 mA mA
MCS-COF CO smoke detector SLC Standby: .30 mA mA
Alarm: 7.2 mA mA
DNR
5
(non-Relay) None, included with ASD-PL2FR
6
DNR
6
(with Relay) None, included with ASD-PL2FR & AOM-2RF
7
Addressable SLC Modules Standby/Alarm .375 mA
mA mA
AMM-4F Monitor module
mA mA
AMM-2F Mini monitor module
mA mA
MS-7ASF Single action pull station
mA mA
MS-7AF Dual action pull station
mA mA
AMM-2IF Dual monitor module Standby/Alarm: .75mA
mA mA
MMI-10F 10 Input monitor module Standby/Alarm: 3.5mA
mA mA
AOM-2SF Control module SLC Standby: .375mA
Alarm: .375mA
mA mA
mA
Aux Pwr
Standby: 1.7mA
mA
Alarm: 7mA
mA
AOM-2RF Relay module SLC
Standby: 2.25mA
mA
Alarm: 2.25mA
mA
Aux Pwr
Standby: 8mA
mA
Alarm: 20mA
mA
Standby/Alarm: .255mA mA mA
MMO-6RF Six relay control module Standby/Alarm: 1.45mA mA mA
AMM-2RIF Dual relay/monitor module Standby: 1.3mA mA
Alarm: 24mA mA
AMM-4SF zone module Aux Pwr Standby: 12mA mAmA
Alarm: 90mA mA mA
SLC Standby/Alarm: .27mA mA mA
MMI-6SF Six zone interface module Aux Pwr Standby: 50mA mA mA
Alarm: 270mAmA mA
SLC Standby/Alarm: 2mA mA mA
B200SR Sounder Base
Aux Pwr Standby: .5mA mA
Alarm: 35mA mA
SLC Standby .3mA mA
Table 3.3 Current Calculation Worksheet for Velociti Devices