Honeywell HC30W45R3 User Manual

78
Honeywell 30 Series IP Cameras User Guide
Note:
• Do not power off the camera during the upgrade.
• If an SD card is used in your camera, backup your SD card contents before the
upgrade.
Follow the steps below to upgrade the firmware:
1. Go to Setup  System Setup  Maintenance  GENERAL SETTINGS.
2. Click CHOOSE FILE and locate the firmware file.
3. Click UPGRADE. The camera starts to upgrade and will reboot automatically when the
upgrade completes.
Note:
•
If an SD card is used in your camera, it will be formatted automatically after the
upgrade. The formatting takes 5 to 20 minutes.
• After the SD card is formatted, it will be encrypted and its content cannot be
read on other cameras.
• If you want to use the SD card in another camera, format the SD card in another
camera first. For how to format the SD card, see
SD Card Format on page 70 .
• A new SD card inserted to camera will also be formatted automatically after the
camera is upgraded.
If the upgrade is successful, the “Reboot system now!! This connection will close”
message will be displayed. After that, re-access the camera. If an SD card is inserted to
the camera, wait for the SD card formatting to complete.
If the power is disconnected during firmware upgrade or if there is unknown reason
causing abnormal LED status, and a Restore cannot recover normal working condition,
you can perform the following steps to activate the camera with its backup firmware:
1. Press and hold down the reset button for at least one minute.
2. Power on the camera until the Red LED blinks rapidly.
3. After booting up, the firmware returns to the previous version before the camera
hanged and the LED status returns to normal. The procedure takes 5 to 10 minutes,
longer than the normal boot-up process.
Rebooting the Camera
On this page, you can reboot the camera. It takes about one minute to complete and
then the live video page will be displayed in your browser.
If the connection fails after rebooting, manually enter the IP address of the camera in
the address field to resume the connection.

Honeywell HC30W45R3 Specifications

General

Type	IP security camera
Placement supported	Indoor & outdoor
Connectivity technology	Wired & Wireless
Wide Dynamic Range (WDR)	Yes
Maximum operating distance	30 m
IK code	IK10
Form factor	Spherical
Mounting type	Ceiling/wall
Product color	Black, White
International Protection (IP) code	IP66
White balance	Auto, Manual
Minimum illumination	0.03 lx
Bit rate control	Constant Bit Rate (CBR)
Total megapixels	5 MP
Gain control type	Auto
Maximum resolution	2560 x 1920 pixels
Video formats supported	H.264, H.265
Analog signal format system	NTSC, PAL
Supported graphics resolutions	640 x 480 (VGA), 800 x 600 (SVGA), 1280 x 960, 1600 x 1200 (UXGA), 2048 x 1536 (QXGA), 2560 x 1920
Sensor type	CMOS
Number of sensors	1
Optical sensor size	1/2.7 \
Lens diameter	2.8 mm
Fixed focal length	2 mm
Maximum aperture number	2
Wi-Fi	No
Number of users	10 user(s)
Ethernet interface type	Gigabit Ethernet
Compatible memory cards	MicroSD (TransFlash), MicroSDHC, MicroSDXC
Maximum memory card size	256 GB
DC output voltage	12
Power source type	DC, PoE
Power consumption (max)	6.49 W
Operating temperature (T-T)	-30 - 60 °C
Operating relative humidity (H-H)	0 - 90 %
Windows operating systems supported	Windows 10, Windows 7

Weight and Dimensions

Depth	89.51 mm
Width	117.11 mm
Weight	540 g
Package weight	880 g