HP HPE VAN SDN Controller 2.7 - Page 205

\"domain\": \"$domain\",
\"user\": \"$user\",
\"password\": \"$pass\"
}
}"
# Attempt to authenticate and extract token if successful.
auth=$(curl --noproxy $nodeIP -X POST --fail -ksSfL --url "$url" \
-H "Content-Type: application/json" --data-binary "$login" 2>&1)
if [ $? -ne 0 ]; then
teamBackup_log "Unable to authenticate as user $user in $domain domain."
exitBackup 1
fi
authToken='extractJSONString "$auth" "token" | sed '/^$/d''
if [ $restore_mode -ne 1 ] && [ "$authToken" == "" ]; then
teamBackup_log "Failed to get the authentication token."
exitBackup 1
fi
echo $authToken
}
#==============================================================================
# M A I N
#==============================================================================
restore_mode=0
# Check for zip package.
command -v zip &> /dev/null
if [ $? -ne 0 ]; then
echo "The zip package must be installed to use this script."
exit 1
fi
# Check the user specified script parameters.
if [ $# -lt 2 ]; then
echo "Usage : backupTeam <user> <domain> [<user@ip:path>]"
echo " <user> - user name to access the controller"
echo " <domain> - domain of the controller"
echo " [<user@ip:path>] - remote location to store backup file"
echo " user - the login name for the system"
echo " ip - the ip address of the system"
echo " path - where to copy the file to on the remote system"
exit 1
fi
validateTeamBackupStatus
user="$1"
echo -n "Enter Controller Password: "
read -s pass
echo
domain="$2"
remotePath=$3
errorCode=0
# Get the authentication token for the local controller.
leaderAuth='getAuthToken localhost'
# Get the system Information for the local controller.
getSysInfo $leaderAuth
# Get the set of team IPs and their associated team roles.
extractRole_NodeIP $sysInfo
(validateTeamLead)
# Initiate a backup on each node.
for (( i=0; i<$numNodes; i++ )); do
nodeAuth[$i]='getAuthToken ${ipArr[$i]}'
uuidURL="https://${ipArr[$i]}:8443/sdn/v2.0/systems"
nodeUUID[$i]='get ${ipArr[$i]} ${nodeAuth[$i]} "$uuidURL?ip=${ipArr[$i]}"'
nodeUUID[$i]='extractJSONString "${nodeUUID[$i]}" "uid" | sed '/^$/d''
if [ "${ipArr[$i]}" == "$leaderIp" ]; then
# Skip the leader backup backup, since it will be done last.
leaderIndex=$i
continue
fi
backupNode $i
teamBackup_log "Started backup on ${ipArr[$i]}."
done
# Verify the status of the backup on each node.
backup_complete=$numNodes
waitTime=$(($BACKUP_WAIT_COUNT*10/60))
for (( k=0; k<$BACKUP_WAIT_COUNT; k++ )); do
if [ $backup_complete -le 1 ]; then
teamBackup_log "Backup on all member nodes completed successfully."
break
fi
sleep 10
for (( i=0; i<$numNodes; i++ )); do
# Skip the leader node check, since it will be done last.
[ "${ipArr[$i]}" == "$leaderIp" ] && continue
# Backup already completed for this node, so continue.
[ "${backupStatus[$i]}" == "SUCCESS" ] && continue
verifyBackupStatus $i
done
done
if [ $backup_complete -gt 1 ]; then
teamBackup_log "Backup of all member nodes took longer than $waitTime min. Aborting backup..."
teamBackup_log "To increase backup wait time, change BACKUP_WAIT_COUNT in the script."
Backing up a controller team 205