HP NonStop SSH 544701-014

HP NonStop SSH Reference Manual Installation & Quick Start • 37
With this parameter set to false, users will be prompted if they want to continue a connection to an
unknown host.
Note: When you start SSH2 in NOWAIT mode, make sure you have disabled logging to the home terminal. To
do so, set the following PARAM:
PARAM LOGCONSOLE *
2. SSH2 will now start with the parameters specified in the command line. It will output initialization messages to
your terminal. Please check these messages for any errors.
Note: Set the DEFINE =TCPIP^PROCESS^NAME or the parameter SUBNET accordingly if you want to run SSH2
over a TCP/IP process other than $ZTC0.
Upon first startup, SSH2 will create a HOSTKEY for the DAEMON mode, which may take a few seconds, depending on
the speed of your system. SSH2 will also create the SSHCTL configuration data base.
Note: If you have installed SSH2 on a non-audited disk volume, SSH2 will fail to open the SSHCTL with error 80
(Invalid operation on audited file or non-audited disk volume). For testing, you may add SSHCTLAUDIT FALSE to the
startup parameters to work around this problem. For a production installation, however, it is strongly recommended that
you have SSHCTL audited. Use the SSHCTL parameter to specify a filename on an audited disk volume, if required.
A normal startup output looks similar to the following screen shot:
$SSH55|26Mar12 21:01:54.55|20|----------------------------------------------------------------
$SSH55|26Mar12 21:01:54.55|10|SSH2 version T9999H06_13Mar2012_comForte_SSH2_0092
$SSH55|26Mar12 21:01:54.56|10|config file: '(none)'
$SSH55|26Mar12 21:01:54.56|20|object filename is '\NPNS01.$US.SSH92DI.SSH2'
$SSH55|26Mar12 21:01:54.56|20|object subvolume is '\NPNS01.$US.SSH92DI', priority is 11
$SSH55|26Mar12 21:01:54.70|20|dumping configuration:
[def ] ALLOWEDAUTHENTICATIONS <keyboard-interactive,password,publickey>
[def ] ALLOWEDSUBSYSTEMS <sftp,tacl>
[def ] ALLOWFROZENSYSTEMUSER <FALSE>
[def ] ALLOWINFOSSH2 <ALL>
[def ] ALLOWPASSWORDSTORE <TRUE>
[def ] ALLOWTCPFORWARDING <FALSE>
[def ] AUDITCONSOLE <*>
[def ] AUDITFILE <*>
[def ] AUDITFILERETENTION <10>
[def ] AUDITFORMAT <21>
[def ] AUDITMAXFILELENGTH <20000>
[def ] BACKUPCPU <NONE>
[def ] BANNER <*>
[def ] CIPHERS <aes256-cbc,twofish256-cbc,twofish-cbc,aes128-cbc,twofish128-cbc,blowfish-cbc,3des-cbc,arcfour,cast128-cbc>
[def ] CLIENTALLOWEDAUTHENTICATIONS <none,gssapi-with-mic,publickey,password,keyboard-interactive>
[def ] CLIENTMODEOWNERPOLICY <BOTH>
[def ] COMPRESSION <TRUE>
[def ] CONFIG <>
[def ] CONFIG2 <*>
[def ] CPUSET <>
[run ] CUSTOMER <comForte GmbH>
[def ] ENABLESTATISTICSATSTARTUP <FALSE>
[def ] EXECTACL <TRUE>
[def ] FULLSSHCOMACCESSGROUP1 <>
[def ] FULLSSHCOMACCESSUSER1 <>
[def ] GSSAUTH <*>
[def ] GSSGEXKEX <FALSE>
[def ] GSSKEX <TRUE>
[def ] GUARDIANATTRIBUTESEPARATOR <,>
[def ] HOSTKEY <HOSTKEY>
[def ] INTERFACE <0.0.0.0>
[def ] INTERFACEOUT <0.0.0.0>
[def ] INTERVALLIVEPRIVATEUSERKEY <730>
[def ] INTERVALLIVEPUBLICUSERKEY <730>
[def ] INTERVALPENDINGPRIVATEUSERKEY <0>
[def ] INTERVALPENDINGPUBLICUSERKEY <0>
[def ] IPMODE <IPV4>
[def ] LICENSE <\NPNS01.$US.SSH92DI.LICENSE>
[def ] LIFECYCLEPOLICYPRIVATEUSERKEY <DISABLED>
[def ] LIFECYCLEPOLICYPUBLICUSERKEY <DISABLED>
[def ] LOGCACHEDUMPONABORT <TRUE>
[def ] LOGCACHESIZE <1024>
[def ] LOGCONSOLE <%>
[def ] LOGEMS <*>
[def ] LOGEMSKEEPCOLLECTOROPENED <TRUE>
[def ] LOGFILE <*>
[def ] LOGFILERETENTION <10>
[def ] LOGFORMATCONSOLE <93>
[def ] LOGFORMATEMS <16>
[def ] LOGFORMATFILE <93>
[def ] LOGLEVELCACHE <50>