By default, the user name and password are admin and Admin@123 respectively for logging
in to the USG6000 through the console port. If you forget the user name and password
configured on the console port, see Password of the Console Port Is Forgotten.
Step 5 Configure upgrade environment.
l Configure Telnet for login.
Enable the Telnet service on GE 0/0/0 of the device. Configure AAA authentication and
Telnet for the virtual type terminal (VTY) user interface. Create a local Telnet user and
set the user name to user1, and password to Password1 for the Telenet user. Enable the
Telnet service on the device.
V500R001:
<FW> system-view
[FW] telnet server enable
[FW] interface GigabitEthernet 0/0/0
[FW-GigabitEthernet1/0/3] ip address 192.168.1.1 255.255.255.0
[FW-GigabitEthernet1/0/3] service-manage telnet permit
[FW-GigabitEthernet1/0/3] service-manage enable
[FW-GigabitEthernet1/0/3] quit
[FW] user-interface vty 0 4
[FW-ui-vty0-4] authentication-mode aaa
[FW-ui-vty0-4] user privilege level 3
[FW-ui-vty0-4] quit
[FW] aaa
[FW-aaa] authorization-scheme default
[FW-aaa-auth-default] quit
[FW-aaa] manager-user user1
[FW-aaa-manager-user-user1] password cipher Password1
[FW-aaa-manager-user-user1] level 15
[FW-aaa-manager-user-user1] service-type telnet
[FW-aaa-manager-user-user1] quit
[FW-aaa] bind manager-user user1 role system-admin
[FW-aaa] quit
[FW] firewall zone trust
[FW-zone-trust] add interface GigabitEthernet1/0/3
[FW-zone-trust] quit
l Configure SSH for login.
Enable the SSH service on GE 0/0/0 of the device. Configure AAA authentication and
SSH for the virtual type terminal (VTY) user interface. Create a local SSH user and set
the user name to user1, and password to Password1 for the SSH user. Enable the
STelnet service on the device.
V500R001:
<FW>system-view
[FW] interface GigabitEthernet 1/0/3
[FW-GigabitEthernet1/0/3] ip address 192.168.1.1 255.255.255.0
[FW-GigabitEthernet1/0/3] service-manage enable
[FW-GigabitEthernet1/0/3] service-manage ssh permit
[FW] quit
[FW] user-interface vty 0 4
[FW-ui-vty0-4] authentication-mode aaa
[FW-ui-vty0-4] user privilege level 3
[FW-ui-vty0-4] protocol inbound ssh
[FW-ui-vty0-4] quit
[FW] aaa
[FW-aaa] manager-user user1
[FW-aaa-manager-user-user1] password cipher Password1
[FW-aaa-manager-user-user1] level 15
[FW-aaa-manager-user-user1] service-type ssh
[FW-aaa-manager-user-user1] quit
[FW-aaa] bind manager-user user1 role system-admin
[FW-aaa] quit
[FW] stelnet server enable
[FW] ssh user user1
HUAWEI USG6000&USG9500
Upgrade Guide
1 USG6000
Issue 01 (2018-01-16) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
91
To Next Page
Loading...
