EasyManuals Logo
Home>IBM>Storage>Storwize V7000 Unified Series

IBM Storwize V7000 Unified Series User Manual

IBM Storwize V7000 Unified Series
314 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #174 background imageLoading...
Page #174 background image
1. To help you work safely with Storwize V7000 Unified file modules, read the
safety information in “Safety” on page xi, “Safety statements” on page xiii,
and “Installation guidelines” on page 54.
2. To query and record the PCI slot settings prior to removing the system board
so that you can reapply the settings after the replacement, use the following
Advanced Settings Utility (ASU) command:
# asu show all --kcs | grep uEFI.PCIeGenSelection
uEFI.PCIeGenSelection.1=Gen2
uEFI.PCIeGenSelection.10=Gen2
uEFI.PCIeGenSelection.11=Gen2
uEFI.PCIeGenSelection.12=Gen2
uEFI.PCIeGenSelection.13=Gen2
uEFI.PCIeGenSelection.14=Gen2
uEFI.PCIeGenSelection.15=Gen2
uEFI.PCIeGenSelection.16=Gen2
uEFI.PCIeGenSelection.2=Gen1
uEFI.PCIeGenSelection.3=Gen2
uEFI.PCIeGenSelection.4=Gen2
uEFI.PCIeGenSelection.5=Gen2
uEFI.PCIeGenSelection.6=Gen2
uEFI.PCIeGenSelection.7=Gen2
uEFI.PCIeGenSelection.8=Gen2
uEFI.PCIeGenSelection.9=Gen2
Some of the PCI slots might be set to the Gen1 value instead of the default
Gen2 value. To reuse the same card in that slot, you must change the setting of
the new system board in the replacement procedure.
3. Turn off the file module and peripheral devices, then label and disconnect
both power cords and all external cables.
4. Pull the power supplies out of the rear of the server; just enough to disengage
them from the server.
5. Press down on the left and right side latches and pull the server out of the
rack enclosure until both slide rails lock.
6. Remove the cover, as described in “Removing the cover” on page 83.
7. Remove the PCI riser-card assembly that contains the adapter, as described in
“Removing a PCI riser-card assembly” on page 99.
v If you are removing an adapter from PCI expansion slot 1 or 2, remove PCI
riser-card assembly 1.
v If you are removing an adapter from PCI expansion slot 3 or 4, remove PCI
riser-card assembly 2.
8. Remove the SAS controller assembly, which includes the SAS riser card, from
the server, as described in “Removing the SAS riser-card and controller
assembly” on page 111.
9. If an Ethernet daughter card is installed in the server, remove it.
10. If a virtual media key is installed in the server, remove it, as described in
“Removing the IBM virtual media key” on page 97.
11. Remove the DIMM air baffle, as described in “Removing the DIMM air baffle”
on page 93.
12. Remove the microprocessor 2 air baffle, as described in “Removing the
microprocessor 2 air baffle” on page 90.
13. Remove all DIMMs, and place them on a static-protective surface for
reinstallation, as described in “Removing a memory module” on page 130.
Important: Note which DIMMs are in which connectors, before you remove
the DIMMs. You must install them in the same configuration on the
replacement system board.
150 Storwize V7000 Unified: Problem Determination Guide Version

Table of Contents

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the IBM Storwize V7000 Unified Series and is the answer not in the manual?

IBM Storwize V7000 Unified Series Specifications

General IconGeneral
BrandIBM
ModelStorwize V7000 Unified Series
CategoryStorage
LanguageEnglish

Related product manuals