EasyManuals Logo

IBM TS3500 Introduction And Planning Guide

IBM TS3500
290 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #101 background imageLoading...
Page #101 background image
An IPv6 (Normal) address has the following format: y:y:y:y:y:y:y
:ywhere y is called a segment and can be any hexadecimal value between 0 and
FFFF. The segments are separated by colons - not periods. An IPv6 normal address
must have eight segments, however a short form notation can be used in the Tape
Library Specialist Web interface for segments that are zero, or those that have
leading zeros. The short form notation can not be used from the operator panel.
Examples of valid IPv6 (Normal) addresses:
v 2001 : db8: 3333 : 4444 : 5555 : 6666 : 7777 : 8888
v 2001 : db8 : 3333 : 4444 : CCCC : DDDD : EEEE : FFFF
v ::(implies all 8 segments are zero)
v 2001: db8: : (implies that the last six segments are zero)
v : : 1234 : 5678 (implies that the first six segments are zero)
v 2001 : db8: : 1234 : 5678 (implies that the middle four segments are zero)
v 2001:0db8:0001:0000:0000:0ab9:C0A8:0102 (This can be compressed to
eliminate leading zeros, as follows: 2001:db8:1::ab9:C0A8:102 )
Here is an example of a screen that uses IPv6 addresses:
Ethernet IPv6 Panel 0178
Current Settings
Frame 1, Port B÷
MAC Address: 18:36:F3:98:4F:9A
Manual IP (IPv6): 684D:1111:222:3333:4444:5555:6:77
DHCP IP (IPv6): Disabled
Stateless Auto IP (IPv6): 0:0:0:0:0:0:0:0
Press ENTER to Change Settings
[BACK] [ UP ] [DOWN] [ENTER]
An IPv6 (Dual) address combines an IPv6 and an IPv4 address and has the
following format: y:y:y:y:y:y:x.x.x.x. The IPv6 portion of
the address (indicated with y's) is always at the beginning, followed by the IPv4
portion (indicated with x's).
v In the IPv6 portion of the address, y is called a segment and can be any
hexadecimal value between 0 and FFFF. The segments are separated by colons -
not periods. The IPv6 portion of the address must have six segments but there is
a short form notation for segments that are zero.
v In the IPv4 portion of the address x is called an octet and must be a decimal
value between 0 and 255. The octets are separated by periods. The IPv4 portion
of the address must contain three periods and four octets.
Examples of valid IPv6 (Dual) addresses:
v 2001 : db8: 3333 : 4444 : 5555 : 6666:1.2.3.4
v ::11.22.33.44(implies all six IPv6 segments are zero)
v 2001 : db8: : 123 . 123 . 123 . 123 (implies that the last four IPv6 segments
are zero)
v ::1234:5678:91.123.4.56(implies that the first four IPv6 segments
are zero)
v ::1234:5678:1.2.3.4(implies that the first four IPv6 segments are
zero)
Chapter 1. Introduction 77

Table of Contents

Other manuals for IBM TS3500

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the IBM TS3500 and is the answer not in the manual?

IBM TS3500 Specifications

General IconGeneral
TypeTape Library
ModelTS3500
Max. drivesUp to 192
InterfaceFibre Channel, SAS
EncryptionYes
Tape TechnologyLTO, IBM TS11xx
Drive supportIBM TS1160

Related product manuals