EasyManuals Logo

Icom IC-F7000 Instruction Manual

Icom IC-F7000
68 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #66 background imageLoading...
Page #66 background image
D General
Frequency coverage : (Unit: MHz)
Receive 0.5–29.9999
Transmit 1.6–5.4999 5.73–5.9999
6.7–8.0999 10.0–11.1999
13.4–14.9999 18.0–18.9999
20.0–20.9999 23.0–27.9999
•Type of emission : J3E (USB/LSB), J2B (AFSK),
(depends on version)
F1B (FSK), A1A (CW),
A3E (AM)
No. of memory Ch. : 500 channels (max.)
Usable temp. range : –10˚C to +60˚C
Frequency stability : ±50 Hz
Power supply : 13.8 V DC
(negative ground)
(10.8–15.6 V DC)
Current drain :
Transmit
(typical)
at max. power 23 A [AUS]
28 A [OTH]
Receive at max. audio 3.0 A
Dimensions (projections not incl.):
Main unit 240(W)×72(H)×239(D) mm
Controller (RC-26) 150(W)×50(H)×51(D) mm
Speaker (SP-25) 106(W)×62(H)×46(D) mm
Microphone (HM-155)
65(W)×105(H)×35(D) mm
•Weight (approx.) :
Main unit 4.6 kg
Controller (RC-26) 220 g without cable
Speaker (SP-25) 370 g
Microphone (HM-155)
234 g
Accessary connector : 8-pin DIN connector
Controller connector : 8-pin MINI DIN connector
REMOTE connector : D-sub 9-pin
(RS-232C/NMEA)
D Transceiver
Output power :
1.6–27.9999 MHz 100/50/10 W p-p [AUS]
1.6–3.9999 MHz 125/50/10 W p-p [OTH]
4.0–27.9999 MHz 100/50/10 W p-p [OTH]
Spurious emission : Less than –43 dB
below peak output power
(Less than –40 dB for 3.5–
3.9999 MHz range [OTH])
Carrier suppression : More than 40dB
below peak output power
Unwanted sideband : More than 50 dB
suppression below peak output power
Mic. connector : 8-pin modular jack
(2.4 k)
D Receiver
Sensitivity:
J3E, A1A
(0.5–1.5999 MHz) 28 dBµV emf (20 dB SINAD)
14 dBµV (10 dB S/N)
(1.8–29.9999 MHz) 0 dBµV emf (20 dB SINAD)
–14 dBµV (10 dB S/N)
A3E
(0.5–1.5999 MHz) 46 dBµV emf (20 dB SINAD)
32 dBµV (10 dB S/N)
Spurious response rejection ratio:
(1.6–29.9999 MHz) More than 70 dB
AF output power:
(at 13.8 V DC)
Main unit More than 4.0 W at 10%
distortion with a 4 load
Controller (RC-26) More than 2.0 W at 10%
distortion with a 4 load
CLARITY variable range
: ±150 Hz
•SP connector:
Main unit 2-conductor
3.5 (d) mm (
1
8)/4
Controller (RC-26) 2-conductor
3.5 (d) mm (
1
8)/4
All stated specications are typical and subject to change without notice or obligation.
8
63
SPECIFICATIONS

Other manuals for Icom IC-F7000

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Icom IC-F7000 and is the answer not in the manual?

Icom IC-F7000 Specifications

General IconGeneral
BrandIcom
ModelIC-F7000
CategoryTransceiver
LanguageEnglish

Related product manuals