Home
IDEAL
Test Equipment
SIGNALTEK
IDEAL SIGNALTEK User Manual
4
of 1
of 1 rating
81 pages
Give review
Manual
Specs
To Next Page
To Next Page
To Previous Page
To Previous Page
Loading...
SIGNALTEK Operation Manual
2-11
Measurement Units
This function controls how the cable length measurements are
displayed. The options are feet (
ft) or m
eters (m).
Figure
2-14 Measurement Units
Date and Time
The tester includes a real-time clock to mark the date and time of
each Autotest. When the batteries are removed the internal clock
will operate for approximately 24 hours, after which the date and
time will need to be reset.
Figure
2-15 Date and Time
www.vemco.pl
38
40
Table of Contents
Default Chapter
6
Table of Contents
6
Table of Figures
8
1 Introduction
11
Cable Qualification Testing
11
SIGNALTEK Test Functions
13
Cable Types
14
Figure 1-1 T-568 A/B Color Code
15
Cable Types that Can be Tested with SIGNALTEK
16
Test Port and Cable Adapters
16
Standard Accessories
16
Optional Accessories
17
Memory
17
Tests
17
Figure 1-2 SIGNALTEK Handsets
19
Batteries & Power
22
Figure 1-3 Battery Discharge Characteristics
23
Battery Charging Warnings
24
Graphical User Interface Navigation
25
User Interface Navigation
26
Figure 1-4 Autotest Tab - Active
26
Figure 1-5 Autotest Tab - Inactive
27
2 Setup and Configuration
29
Wire Map Display Color Code
29
Figure 2-1 Setup Tab
29
Autotest Preferences
30
Figure 2-2 Wire Map Display Preferences
30
Figure 2-3 Autotest Preferences
30
Autotest Modes
31
Figure 2-4 Remote Detected
31
Figure 2-5 Active LAN (Link) Detected
31
Figure 2-6 no Link Detected
31
Cable Performance Setup
32
Figure 2-7 Cable Performance Setup
33
IP Address Setup
34
Figure 2-8 Voip Setup
34
Ping Setup
35
Figure 2-9 IP Address Setup
35
Device Defaults
36
Figure 2-10 Ping Setup
36
Owner Information
37
Display Preferences
37
Figure 2-11 Owner Information
37
Timeout Options
38
Figure 2-12 Display Contrast
38
Figure 2-13 Timeout Options
38
Measurement Units
39
Date and Time
39
Figure 2-14 Measurement Units
39
Figure 2-15 Date and Time
39
Cable ID Prefix
40
Figure 2-16 Cable ID Prefix Setup
40
Language
41
Restore Factory Defaults
41
Figure 2-17 Language Setup
41
Figure 2-18 Factory Defaults
41
Updating Firmware
42
Figure 2-19 Firmware Version
42
3 Test Storage and Management
45
Using the Job Tab Functions
45
Figure 3-1 Job Tab
45
Printing and Copying to USB Drives
46
Direct PC Connection (Windows XP™ Only)
47
Copy to External USB Drive
47
Printing Directly to a USB Printer
48
Figure 3-2 USB Printer Cable
48
4 Running Autotests
49
Figure 4-1 Autotest Tab
49
Beginning an Autotest
50
Stopping an Autotest
51
Active Link Testing
51
No-Link Testing
52
Manual Tests
52
5 Test Results
53
Wire Map Results
53
Figure 5-1 Wire Map Results
53
Wire Map Testing Active LAN Links
54
Link Establishment
54
Bit Error Rate Tests
55
Figure 5-2 Link Establishment Results
55
Figure 5-3 Cable Performance Results
56
Performance Test Failures
57
6 Fiber Optic Testing
59
Overview
59
Fiber Qualification Abilities
60
Figure 6-1 SIGNALTEK-FO Top Connectors
60
Figure 6-2 LC-To-SC Cable
61
Figure 6-3 SC Coupler
61
Setup and Calibration
62
7 Troubleshooting & Frequently Asked Questions
65
8 Care and Calibration
73
9 Specifications
75
10 Customer Service
77
IDEAL INDUSTRIES World Wide Contact Information
78
4
Based on 1 rating
Ask a question
Give review
Questions and Answers:
Need help?
Do you have a question about the IDEAL SIGNALTEK and is the answer not in the manual?
Ask a question
IDEAL SIGNALTEK Specifications
General
Brand
IDEAL
Model
SIGNALTEK
Category
Test Equipment
Language
English
Related product manuals
IDEAL SureTrace
93 pages
IDEAL SecuriTEST
40 pages
IDEAL SecuriTest IP
63 pages
IDEAL Volt Sensor 61-063
3 pages
IDEAL ABS
1 page
IDEAL 61-520
2 pages
IDEAL 61-534
6 pages
IDEAL 61-085
19 pages
IDEAL 61-521
12 pages
IDEAL 61-795
36 pages
IDEAL Vol-Con XL
5 pages
IDEAL Vol-Con 61-076
11 pages
To Next PageTo Next PageTo Previous PageTo Previous Page
Loading...
Need help?
General
