Incon OPTImizer 2 - Alarm History Report; Table 8: Alarm Codes

55
Alarm History Report
The Alarm History Report consists of: Code; Category; Device; Data; State; (Date & Time) Occurred and (Date & Time)
Cleared.
Code: The alarm Code is an abbreviation for the description of the alarm seen on the ALARM tab. The prex “al” is used to
indicate that it is an Alarm code. The table below gives a description of each alarm Code:
Code: Description: Cause: How to Clear:
alInvalidConguration
Invalid Setup
Conguration
The unit has not been
programmed
Enter conguration settings
alCongurationDNP3
Invalid DNP3
Conguration
DNP3 settings are illegal Reprogram DNP3 settings
alWarningLimit
Remaining Contact
Life Warning Limit
Contact Life has reached
the Warning Limit
On ACTION Tab: Preset Remaining
Contact Life below the Warning Limit
alDangerLimit
Remaining Contact
Life Danger Limit
Contact Life has reached
the Danger Limit
On ACTION Tab: Preset Remaining
Contact Life below the Danger Limit
alArcTimeLimit Arc Time Limit
Excess Arc Time has
been detected
On ACTION Tab: Clear Latched Alarms
alRestrike Restrike
A Restrike has been
detected
On ACTION Tab: Clear Latched Alarms
alClearingTimeLimit Clearing Time Limit
Excess Clearing Time
has been detected
On ACTION Tab: Clear Latched Alarms
alTripTimeLimit Trip Time Limit
Excess Trip Time has
been detected
On ACTION Tab: Clear Latched Alarms
alTravelTimeLimit Travel Time Limit
Excess Travel Time has
been detected
On ACTION Tab: Clear Latched Alarms
alClosingTimeLimit Closing Time Limit
Excess Closing Time has
been detected
On ACTION Tab: Clear Latched Alarms
alOperationCountLimit
Operation Count
Limit
Operation Count has
reached the Limit
On ACTION Tab: Reset Operations
Counter
alNoOperationsTimeLimit
No Operations Time
Limit
Time between CB
operations too long
Operate the circuit breaker
alABLogicAlarm A-B Logic Alarm
Logic violation on A & B
inputs
Self-clears when the A-B Input logic is
OK
alCongurationCbMonitor
Invalid CB Monitor
Cong.
CB Monitor settings are
illegal
Reprogram CB Monitor settings
alLowGasYellowLimit
SF
6
Low Gas Yellow
Limit
Low SF
6
gas detected Add gas to the CB
alLowGassRedLimit
SF
6
Low Gas Red
Limit
Very low SF
6
gas
detected
Add gas to the CB
alErraticSignal
Erratic Sensor
Signal
Erratic SF
6
Sensor
Signal detected
Self-clears when a signal is stable
alTrendLimit SF
6
Trend Limit
SF
6
Trend Limit has been
reached
Stop loss of SF
6
; On ACTION Tab:
Reset SF
6
Trend Data
alNoSensorSignal
No Sensor Signal
Detected
No SF
6
sensor signal
Detected
Self-clears when a signal is detected
alSignalRangeError
SF
6
Sensor Signal
Range Error
SF
6
sensor signal out of
range
Self-clears when the signal is in range
alCongurationSf6
Invalid SF
6
Conguration
SF
6
Monitor settings are
illegal
Reprogram SF
6
Monitor settings
alCTInputFailure CT Input Failure Bad CT Pickup Coil Check wiring or replace CT Pickup Coil
alInternalError1 Internal Error #1 Data Overload Contact Technical Support
alInputInvalid Input Invalid Software Malfunction Contact Technical Support
alCBMonitorUnknownActity CBM Unknown Activity Software Malfunction Contact Technical Support
alSF6UnknownActivity
SF
6
Unknown
Activity
Software Malfunction Contact Technical Support
alInternalErrorDNP3 Internal DNP3 Error Software Malfunction Contact Technical Support
Table 8: Alarm Codes