Playback
En-35
Tip
• The AV controller may not work as normal depending on
the circumstance even though the AV controller is placed
within the 15 meters range. In such cases, get the
Bluetooth-enabled device closer to the AV controller and
retry the operation.
• When disconnecting on your Bluetooth-enabled device,
Bluetooth indicator on the AV controller will go off.
• If there is no sound output even after the pairing is done
successfully, consult the instruction manual of the
Bluetooth-enabled device, and then select the model name
of the AV controller as the audio output device.
• While connected to a Bluetooth-enabled device, the AV
controller cannot be detected and a connection cannot be
established from another Bluetooth-enabled device.
• If you cannot connect with a paired Bluetooth-enabled
device, perform the pairing operation between the AV
controller and the Bluetooth-enabled device again.
Note
• Due to the characteristic of Bluetooth wireless technology,
the sound played on the AV controller may slightly delay
from the sound played on the Bluetooth-enabled device.
Tip
• The on-screen information appears only on a TV that is
connected to HDMI/HDBaseT™ outputs.
This section explains how to play music files from a
USB device (e.g., USB flash drives and MP3 players).
See also:
• “Network/USB Features” (➔ page 107).
Note
• While the message “Connecting...” appears on the AV
controller’s display, do not disconnect the USB cable
supplied with the USB device from the USB port.
You need to connect the AV controller to your home
network (➔ pages 19, 30).
Tip
• The on-screen information appears only on a TV that is
connected to HDMI/HDBaseT outputs.
TuneIn is a new radio service which offers the music,
sports and news all over the world.
Over 70,000 radio stations and 2 million on-demand
programs are registered, and you can easily enjoy
them by selecting stations or programs of your
choice. TuneIn is preprogrammed on the AV
controller.
3
During this period (about 2 minutes), you can
operate the Bluetooth-enabled device to pair
with the AV controller.
Note
• When establishing a connection with the AV controller,
select the profile (A2DP, AVRCP) at the Bluetooth-
enabled device. If the Bluetooth-enabled device does
not support the AVRCP profile, you cannot perform
playback or other operations with the AV controller.
Tip
• For details on the Bluetooth connection, refer to the
instruction manual of the Bluetooth-enabled device.
4
Once the AV controller is detected and the
model name of the AV controller appears on
the display of your Bluetooth-enabled device,
select the model name.
When a Bluetooth connection is established
successfully, Bluetooth indicator will light.
Tip
• The model name appeared on the display of your
Bluetooth-enabled device is “Integra DHC-60.5”.
The model name displayed on your Bluetooth-enabled
device can be changed in Web Setup (➔ page 37).
5
If passkey
*
is required on the display of the
Bluetooth-enabled device, enter “0000”.
The AV controller only supports numerical
passkey up to 4 digits.
* Passkey may be called “Passcode”, “PIN code”, “PIN
number” or “Password”.
6
Play back the desired music on the Bluetooth-
enabled device.
The audio is output from the AV controller.
Playing a USB Device
1
Press USB to select the “USB” input.
2
Plug your USB device into the AV controller’s
USB port.
The USB indicator lights. It will flash if the AV
controller cannot read the USB device.
3
Press Enter.
A list of the device’s contents appears. To open a
folder, use q/w to select it, and then press Enter.
4
Use q/w to select a music file, and press Enter
or 1 to start playback.
Listening to TuneIn
1
Press NET.
The network service screen appears, and the
NET indicator lights. If it flashes, the AV controller
is not connected to the network correctly. If wired
LAN connection is selected, verify that the
Ethernet cable is firmly connected to the AV
controller. If wireless LAN connection is selected,
verify that the Wi-Fi indicator lights.
Tip
• The same operation can be done by selecting
“Network Service” in the Home menu.
2
Use q/w/e/r to select “TuneIn” and then
press Enter.
To Next Page
Loading...
Need help?
General